Technical Data - DAEWOO G 15 MF
Manufacturer DAEWOO
G 15 MF - I -
| Engine Type | G 15 MF |
| Fuel Supply System | I |
| Note |
| Cc | 1498 |
| Number of Cylinders | 4 |
| Bore Ø | 76.50 |
| Stroke | 81.50 |
| KW | 55 |
| Compression | 8.6 |
| KBA No. (Germany) | 4114371 |
| Type Mines | 905A3C |
| Technical Information Number | Technical Data | Information |
|---|---|---|
| ····Engine Code | ||
| Compression-------------- | ||
| ····Compression - Ratio | ||
| ····Compression - Pressure [bar] | ||
| ····Wear limitation | ||
| Refs------ | ||
| ····Idle, min. | ||
| ····Idle, Max. | ||
| Exhaust Gas, value------- | ||
| ····CO Measurement, Idle | ||
| ····CO2 Measurement, Idle [%] | ||
| ····HC Measurement, Idle | ||
| Oil Pressure------------- | ||
| Thermostat | ||
| ····Thermostat, Opening Temperature | ||
| Ignition Timing---------- | ||
| ····Ignition System | ||
| Ignition - Row----------- | ||
| =<>= | ||
| Valves---- | ||
| ··Valve Clearance [mm] | ||
| ··Valves - Length (L) | ||
| ····Centering - Valve Stem (Tolerance) | ||
| ··Valve stem diameter [d] - Inlet | ||
| ····Standard Size | ||
| ··Valve stem diameter [d] - Exhaust | ||
| ····Standard Size | ||
| ··Valve seat - Width S (Contact - Surface) | ||
| ··Valve Seat Angle [°] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Disc | ||
| Valve Spring------------- | ||
| ··Capacitive Load => Length 1 [mm] | ||
| ··Capacitive Load => Length 2 [mm] | ||
| Valve Guides------------- | ||
| ··Inner Diameter - Standard Size | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Clearance - Valve => Valve Guides | ||
| ····Inlet | ||
| ····Exhaust | ||
| Camshaft-- | ||
| ··Bore - Holder, Camshaft Bushes (Standard Size) | ||
| ····1st Bearing | ||
| ····2nd Bearing | ||
| ····3rd Bearing | ||
| ····4th Bearing | ||
| ····5th Bearing | ||
| ··Diameter, Bearing Journal - Camshaft (Standard Size) | ||
| ····1st Bearing | ||
| ····2nd Bearing | ||
| ····3rd Bearing | ||
| ····4th Bearing | ||
| ····5th Bearing | ||
| ··Clearance, Radial - Camshaft Bushes | ||
| ··Clearance, Axial - Camshaft Bushes | ||
| ··Valve lift | ||
| ····Inlet | ||
| ····Wear limitation - Inlet | ||
| =<>= | ||
| Cylinder Sleeve---------- | ||
| ··Bore | ||
| ····Standard Size | ||
| ··Measurement - Oval, Bore (Cylinder Sleeve) | ||
| ····Wear limitation | ||
| ··Measurement - Conical | ||
| ····Wear limitation | ||
| ····Wear limitation | ||
| Piston---- | ||
| ··Diameter - Piston | ||
| ····Standard Size | ||
| ··Clearance - Piston | ||
| Gudgeon Pin-------------- | ||
| ··Diameter - Gudgeon Pin | ||
| ··Clearance, Radial - Gudgeon Pin | ||
| ····Clearance, Radial - Piston Rod / Piston | ||
| Piston Ring Set---------- | ||
| ··Piston Ring, Groove | ||
| ··1st Piston Ring, Lock - Clearance (Compression) | ||
| ··2nd Piston Ring, Lock - Clearance (Compression) | ||
| ··1st Piston Ring, Height - Clearance (Compression) | ||
| ··2nd Piston Ring, Height - Clearance (Compression) | ||
| Connecting Rod----------- | ||
| ··Clearance, Radial - Big End Bearing | ||
| ··Clearance, Axial - Big End Bearing | ||
| ··Diameter, Bearing Journal - Connecting Rod | ||
| ··Bearing Journal, Connecting Rod - Conical (Max.) | ||
| Crankshaft | ||
| ··Diameter, Bearing Journal - Crankshaft (Standard Size) | ||
| ··Clearance - Main Bearing, crankshaft | ||
| Cooling System----------- | ||
| ··Clearance - Outer, Rotor => Housing, Oil Pump | ||
| Timing Gear, Kit (Control)- | ||
| ··Clearance - Gear wheel (Tooth Pitch) | ||
| ··Clearance, Axial - Gear wheel | ||
| =<>= | ||
| Engine Timing Control | ||
| Valve Cover-------------- | ||
| Cylinder Head Bolts------ | ||
| ····Replace - Bolts | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| ····Stage 3 | ||
| ····Stage 4 | ||
| ····Stage 5 | ||
| Bearing Cap, connecting rod | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| Crankshaft | ||
| Cranskhaft Pulley-------- | ||
| Flywheel-- | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| Drive gear - Camshaft---- | ||
| Timing Case-------------- | ||
| ··Timing Case, Cover | ||
| ··Timing Belt Tensioner | ||
| Water Pump | ||
| Oil Pan--- | ||
| ··Oil Drain Plug, oil pan | ||
| Exhaust Manifold--------- | ||
| Intake Manifold---------- |
Gain access
Enginedesk contains rich-data for parts and engines. The service is particulary useful for engine rebuilders and maintenance shops.
You can browse all information online. To get access to the technical data and parts information we provide the following options:
- Anytime 'all access' € 25,- * per month.
- Anytime 'all access' € 250,- * yearly.
* Excluding sales tax (21%)
Parts manufacturer
Reach thousands of remanufacturing companies. Promote your aftermarket parts and services world wide.
Please contact Enginedesk via info@enginedesk.com.
