Technical Data - FIAT 8144.97
Manufacturer FIAT
8144.97 - T -
| Engine Type | 8144.97 |
| Fuel Supply System | T |
| Note |
| Cc | 2499 |
| Number of Cylinders | 4 |
| Bore Ø | 93.00 |
| Stroke | 92.00 |
| KW | 85 |
| Compression | 21.00 |
| KBA No. (Germany) | 4114371 |
| Type Mines | 905A3C |
| Technical Information Number | Technical Data | Information |
|---|---|---|
| Charger--- | ||
| ··Type | ||
| ····Manufacturer + Version | ||
| ····Turbocharger - Pressure (Max.) | ||
| Compression-------------- | ||
| ····Compression - Ratio | ||
| Refs------ | ||
| ····Idle, min. | ||
| ····Idle, Max. | ||
| ····RPM, Max. | ||
| Exhaust Gas, value------- | ||
| ····Smoke Grey - Service RPM | ||
| Oil Pressure------------- | ||
| ····Status (Operating Mode / Cold Check) | ||
| ····Idle, min. | ||
| ····Rated Capacity | ||
| Thermostat | ||
| ····Thermostat, Opening Temperature | ||
| Ignition Timing---------- | ||
| ····Ignition System | ||
| Ignition - Row----------- | ||
| ····Ignition Point, Static / Dynamic | ||
| injection pump----------- | ||
| ··Injection - Stage 1 => x | ||
| ··Pressure, Fuel injection | ||
| =<>= | ||
| Injector Nozzle---------- | ||
| ··Bore Ø [mm] - Injector Nozzle | ||
| ··Bore Ø [mm] - Injector Nozzle (Sleeve) | ||
| ··Diameter - Injector Nozzle | ||
| ··Diameter - Injector Nozzle (Sleeve) | ||
| ··Clearance, Radial - Nozzle / Cylinder Head | ||
| ··Clearance, Radial - Nozzle Sleeve / Cylinder Head | ||
| Pre-chamber-------------- | ||
| ··Protrusion -/+, Pre-combustion chamber | ||
| ··Pre-combustion chamber (Press-fitted) - Tolerance | ||
| ··Outer Diameter - Pre-chamber | ||
| ····Standard Size | ||
| ··Bore - Holder, Pre-chamber | ||
| ····Standard Size | ||
| ··Flange, Height | ||
| ····Standard Size | ||
| ····Standard Size | ||
| ····Standard Size | ||
| ··Flange - Fitting Depth [mm] | ||
| ····Standard Size | ||
| ····Standard Size | ||
| ····Standard Size | ||
| Valves---- | ||
| ··Valve Clearance [mm] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Clearance - Cold Check [mm] | ||
| ··Valve Actuation, Setting | ||
| ····Inlet / Open (° before TDC) | ||
| ····Inlet / Closed (° after BDC) | ||
| ····Exhaust / Open (° before BDC) | ||
| ····Exhaust / Closed (° after TDC) | ||
| ··Valve Head Diameter [D] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve stem diameter [d] - Inlet | ||
| ··Valve stem diameter [d] - Exhaust | ||
| ··Valve Seat Angle [°] | ||
| ····Inlet | ||
| ····Exhaust | ||
| Valve Spring------------- | ||
| ··Min. Length [mm] => Capacitive Load 1 | ||
| ····Inner | ||
| ····Outer | ||
| ··Min. Length [mm] => Capacitive Load 2 | ||
| ····Inner | ||
| ····Outer | ||
| Valve Guides------------- | ||
| ··Inner Diameter - Standard Size | ||
| ··Outer Diameter - Standard Size | ||
| ··Outer Diameter - 1st Oversize | ||
| ··Outer Diameter - 2nd Oversize | ||
| ··Outer Diameter - 3rd Oversize | ||
| ··Bore - Holder, Valve Guides (Standard Size) | ||
| ··Clearance - Valve => Valve Guides | ||
| ··Press-fitted, Valve Guides | ||
| Valve seat | ||
| ··Valve Seat Angle (B) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Seat - Measurement (A) | ||
| Valve Lifter------------- | ||
| ··Diameter - Valve Lifter | ||
| ····Standard Size | ||
| ····Standard Size | ||
| ··Bore - Holder, Rocker/ Tappet | ||
| ····Standard Size | ||
| ····Standard Size | ||
| ··Clearance, Radial - Valve Lifter | ||
| Camshaft-- | ||
| ··Bore - Holder, Camshaft Bushes (Standard Size) | ||
| ··Diameter, Bearing Journal - Camshaft (Standard Size) | ||
| ··Clearance, Radial - Camshaft Bushes | ||
| ··Cam Lobe Height (Total) | ||
| ····Inlet | ||
| ····Exhaust | ||
| =<>= | ||
| General Information - Engine Block | ||
| ··Bore - Holder, Main Bearings (Engine Block) | ||
| ··Bore - Holder, Cylinder Sleeve | ||
| ····Standard Size | ||
| ··Press-fitted, Cylinder Sleeve | ||
| Cylinder Sleeve---------- | ||
| ··Inner Diameter - Cylinder Sleeve | ||
| ····Standard Size | ||
| ····Standard Size | ||
| ····Standard Size | ||
| ····Wear limitation | ||
| ··Outer Diameter - Cylinder Sleeve | ||
| ····Standard Size | ||
| Piston---- | ||
| ··Piston Crown Clearance -/+ | ||
| ··Diameter - Piston | ||
| ····Standard Size | ||
| ····Standard Size | ||
| ····Standard Size | ||
| ····Wear limitation | ||
| ····Measurement (Position) | ||
| Gudgeon Pin-------------- | ||
| ··Diameter - Gudgeon Pin (Eye) | ||
| ··Clearance, Radial - Gudgeon Pin | ||
| ····Clearance, Radial - Small End Bush / Piston Rod | ||
| ····Clearance, Radial - Small End Bush / Gudgeon Pin | ||
| Piston Ring Set---------- | ||
| ··Height, 1st Piston Ring (Compression) | ||
| ··Height, 2nd Piston Ring (Compression) | ||
| ··Height, Piston Ring (Oil Trap) | ||
| ··Piston Ring, Groove | ||
| ··1st Piston Ring, Lock - Clearance (Compression) | ||
| ··2nd Piston Ring, Lock - Clearance (Compression) | ||
| ··Piston Ring, Lock - Clearance (Oil Trap) | ||
| ··1st Piston Ring, Height - Clearance (Compression) | ||
| ··2nd Piston Ring, Height - Clearance (Compression) | ||
| ··Piston Ring, Height - Clearance (Oil Trap) | ||
| Connecting Rod----------- | ||
| ··different, Weight - Connecting Rod (Max.) | ||
| ··Bore - Holder, Connecting Rod (Small End Bushes) | ||
| ··Bore - Holder, Connecting Rod (Big End Bearing) | ||
| ··Bore - Holder, Connecting Rod (Big End Bearing) | ||
| ··Clearance, Radial - Big End Bearing | ||
| ··Clearance, Radial - Big End Bearing | ||
| ··Diameter, Bearing Journal - Connecting Rod | ||
| ····Standard Size | ||
| ····Standard Size | ||
| ····Standard Size | ||
| ··Small End Bushes | ||
| ····Inner Diameter | ||
| Crankshaft | ||
| ··Number of bearings | ||
| ··Diameter, Bearing Journal - Crankshaft (Standard Size) | ||
| ··Width, Bearing Journal (Crankshaft) | ||
| ····Standard Size | ||
| ··Clearance - Main Bearing, crankshaft | ||
| ··Bearing clearance - Axial Bearing | ||
| Main Bearing scales, crankshaft ----------------------------- | ||
| ··Thickness, Axial Bearing (Bearing Shell) | ||
| ····Standard Size | ||
| Cooling System----------- | ||
| ··Type | ||
| ··Clearance - Outer, Rotor => Inside, Rotor | ||
| Clearance, Axial - Drive gear => Cover | ||
| ··Clearance, Axial - Driven Gear wheel => Cover | ||
| ··Clearance - Drive gear => Housing, Pump | ||
| =<>= | ||
| Engine Timing Control | ||
| Cylinder Head Bolts------ | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| ····Stage 3 | ||
| Main Bearing Cap, crankshaft -------------------------------- | ||
| Bearing Cap, connecting rod | ||
| Flywheel-- | ||
| Camshaft, Bearing Cap---- | ||
| Drive gear - Camshaft---- | ||
| Exhaust Manifold--------- | ||
| Intake Manifold---------- |
Gain access
Enginedesk contains rich-data for parts and engines. The service is particulary useful for engine rebuilders and maintenance shops.
You can browse all information online. To get access to the technical data and parts information we provide the following options:
- Anytime 'all access' € 25,- * per month.
- Anytime 'all access' € 250,- * yearly.
* Excluding sales tax (21%)
Parts manufacturer
Reach thousands of remanufacturing companies. Promote your aftermarket parts and services world wide.
Please contact Enginedesk via info@enginedesk.com.
