Technical Data - FORD EUROPE FXDA ZETEC SE
Manufacturer FORD EUROPE
FXDA ZETEC SE - I - DOHC - Zetec-SE SFI
| Engine Type | FXDA ZETEC SE |
| Fuel Supply System | I |
| Note | DOHC - Zetec-SE SFI |
| Cc | 1388 |
| Number of Cylinders | 4 |
| Bore Ø | 76.00 |
| Stroke | 76.50 |
| KW | 55 |
| Compression | 10.1 |
| KBA No. (Germany) | 4114371 |
| Type Mines | 905A3C |
| Technical Information Number | Technical Data | Information |
|---|---|---|
| ····Engine Code | ||
| Compression-------------- | ||
| ····Compression - Ratio | ||
| Refs------ | ||
| ····Idle, Max. | ||
| ····RPM, Max. | ||
| Exhaust Gas, value------- | ||
| Oil Pressure------------- | ||
| ····Status (Operating Mode / Cold Check) | ||
| ····Status (Operating Mode / Cold Check) | ||
| ····Status (Operating Mode / Cold Check) | ||
| ····Oil Pressure Valve - Release (bar) | ||
| Ignition Timing---------- | ||
| ····Ignition System | ||
| Ignition - Row----------- | ||
| =<>= | ||
| ··warpage (value) - Cylinder Head | ||
| ····Wear limitation | ||
| Valves---- | ||
| ··Valve Clearance [mm] | ||
| ····Operating Mode / Cold Check | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Actuation, Setting | ||
| ····Inlet / Open (° before TDC) | ||
| ····Inlet / Closed (° after BDC) | ||
| ····Exhaust / Open (° before BDC) | ||
| ····Exhaust / Closed (° after TDC) | ||
| ··Valve Head Diameter [D] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valves - Length (L) | ||
| ····Inlet - New Part | ||
| ····Exhaust - New Part | ||
| Valve Spring------------- | ||
| ··Valve Spring - Length (Load/Empty) | ||
| ····Inner Diameter | ||
| ··Diameter - Spring, Material | ||
| =<>= | ||
| Cylinder Sleeve---------- | ||
| ··Bore | ||
| ····Standard Size | ||
| ····Standard Size | ||
| ····Standard Size | ||
| Piston---- | ||
| ··Diameter - Piston | ||
| ····Standard Size | ||
| ····Standard Size | ||
| ····Standard Size | ||
| Piston Ring Set---------- | ||
| ··Piston Ring, Groove | ||
| ··1st Piston Ring, Lock - Clearance (Compression) | ||
| ··2nd Piston Ring, Lock - Clearance (Compression) | ||
| ··Piston Ring, Lock - Clearance (Oil Trap) | ||
| ··1st Piston Ring, Height - Clearance (Compression) | ||
| ··2nd Piston Ring, Height - Clearance (Compression) | ||
| Crankshaft | ||
| ··Bearing clearance - Axial Bearing | ||
| =<>= | ||
| Valve Cover-------------- | ||
| Cylinder Head------------ | ||
| Cylinder Head Bolts------ | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| ····Stage 3 | ||
| ····Stage 4 | ||
| Main Bearing Cap, crankshaft -------------------------------- | ||
| Bearing Cap, connecting rod | ||
| Crankshaft | ||
| ····Retainer Ring, Shaft Oil Seal (Rear) | ||
| ··Cap, Adjustment Mandrel (° before TDC) | ||
| Vibration Damper, Crankshaft -------------------------------- | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| ··Knock Sensor | ||
| Sensor, crankshaft pulse- | ||
| Flywheel-- | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| Camshaft-- | ||
| ··Sensor, camshaft position | ||
| Camshaft, Bearing Cap---- | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| Pulley, Camshaft--------- | ||
| Timing Case-------------- | ||
| ··Timing Case, Cover | ||
| ··Timing Case, Cover | ||
| ····Upper section | ||
| ····Lower Section | ||
| ··Timing Belt Tensioner | ||
| ··Timing Belt Tensioner | ||
| ··Guide Pulley | ||
| Alternator | ||
| Spark Plug | ||
| Ignition Coil | ||
| Cooling System----------- | ||
| ··Thermostat Housing | ||
| ··Coolant, bridge | ||
| ··Sensor, cylinder head temperature | ||
| Fuel Pump- | ||
| ··Fuel Line | ||
| Oil Pump-- | ||
| ··Pulley | ||
| ··Oil Pressure Switch | ||
| Oil Pan--- | ||
| ··Oil Drain Plug, oil pan | ||
| ··Oil Dipstick - Holder | ||
| ··Pipe, crankcase breather | ||
| ··Oil Filter | ||
| ··Oil Strainer | ||
| Exhaust Manifold--------- | ||
| Exhaust Manifold--------- | ||
| Intake Manifold---------- | ||
| Hook fixing, Engine Block |
Gain access
Enginedesk contains rich-data for parts and engines. The service is particulary useful for engine rebuilders and maintenance shops.
You can browse all information online. To get access to the technical data and parts information we provide the following options:
- Anytime 'all access' € 25,- * per month.
- Anytime 'all access' € 250,- * yearly.
* Excluding sales tax (21%)
Parts manufacturer
Reach thousands of remanufacturing companies. Promote your aftermarket parts and services world wide.
Please contact Enginedesk via info@enginedesk.com.
