Technical Data - KAEBLE & GMEINDER MD 140 (A)-T
Manufacturer KAEBLE & GMEINDER
MD 140 (A)-T - I - V-8 ENGINE
| Engine Type | MD 140 (A)-T |
| Fuel Supply System | I |
| Note | V-8 ENGINE |
| Cc | 18472 |
| Number of Cylinders | 8 |
| Bore Ø | 140.00 |
| Stroke | 150.00 |
| KW | 239 |
| Compression | 16 |
| KBA No. (Germany) | 4114371 |
| Type Mines | 905A3C |
| Technical Information Number | Technical Data | Information |
|---|---|---|
| Compression-------------- | ||
| ····Compression - Ratio | ||
| ····Compression - Pressure [bar] | ||
| Refs------ | ||
| ····Idle, min. | ||
| ····RPM, Max. | ||
| Oil Pressure------------- | ||
| ····Status (Operating Mode / Cold Check) | ||
| ····Idle, min. | ||
| ····Min. | ||
| ····Rated Capacity | ||
| injection pump----------- | ||
| ··Injection - Stage 1 => x | ||
| ····Injection (Point - ° before TDC) | ||
| ··Pressure, Fuel injection | ||
| ····New Part | ||
| =<>= | ||
| General Information - Cylinder Head ------------------------- | ||
| ··Cylinder Head - Number | ||
| ··Material, Surface | ||
| ··Piston Crown Clearance -/+ | ||
| Valves---- | ||
| ··Valve Clearance [mm] | ||
| ····Operating Mode / Cold Check | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Actuation, Setting | ||
| ····Inlet / Open (° before TDC) | ||
| ····Exhaust / Closed (° after TDC) | ||
| ··Valve Head Diameter [D] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Seat Angle [°] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valves, Fitted Height | ||
| ····Inlet | ||
| ····Exhaust | ||
| Valve Guides------------- | ||
| ··Clearance - Valve => Valve Guides | ||
| ····Inlet | ||
| ····Exhaust | ||
| Valve seat | ||
| ··Valve Seat Angle (B) | ||
| ····Inlet | ||
| ····Exhaust | ||
| Camshaft-- | ||
| ··Bearing - Number | ||
| ··Diameter, Bearing Journal - Camshaft (Standard Size) | ||
| ··Clearance, Radial - Camshaft Bushes | ||
| =<>= | ||
| General Information - Engine Block | ||
| ··Cylinder Sleeve Protrusion | ||
| Cylinder Sleeve---------- | ||
| ··Seal (Tombak) - Thickness | ||
| ··Thickness, Flange (Upper section) | ||
| ··Outer Diameter - Flange, Cylinder Sleeve | ||
| ··Bore | ||
| ····Standard Size | ||
| ··Adjustment - Machined (Tolerance) | ||
| ····Inner Diameter | ||
| ··Cylinder Sleeve, Length | ||
| ··Inner Diameter - Cylinder Sleeve | ||
| ····Standard Size | ||
| ··Outer Diameter - Cylinder Sleeve | ||
| ····Standard Size | ||
| Piston---- | ||
| ··Piston Crown Clearance -/+ | ||
| ··Clearance - Piston | ||
| Connecting Rod----------- | ||
| ··Distance, Centre - Small End Bush / Big End Bearing | ||
| ··Clearance, Radial - Big End Bearing | ||
| ····Wear limitation | ||
| ··Diameter, Bearing Journal - Connecting Rod | ||
| ····Standard Size | ||
| ··Small End Bushes | ||
| ····Inner Diameter | ||
| ····Clearance, Radial - Small End Bush / Gudgeon Pin | ||
| Crankshaft | ||
| ··Hardened (Tolerance) | ||
| ··Number of bearings | ||
| ··Centering - Crankshaft (Tolerance) | ||
| ····Crankshaft, Radius [R] | ||
| ··Diameter, Bearing Journal - Crankshaft (Standard Size) | ||
| ··Clearance - Main Bearing, crankshaft | ||
| ··Bearing clearance - Axial Bearing | ||
| =<>= | ||
| Cylinder Head------------ | ||
| Cylinder Head Bolts------ | ||
| ····Replace - Bolts | ||
| ····Stage 1 | ||
| Main Bearing Cap, crankshaft -------------------------------- | ||
| Bearing Cap, connecting rod | ||
| Flywheel-- |
Gain access
Enginedesk contains rich-data for parts and engines. The service is particulary useful for engine rebuilders and maintenance shops.
You can browse all information online. To get access to the technical data and parts information we provide the following options:
- Anytime 'all access' € 25,- * per month.
- Anytime 'all access' € 250,- * yearly.
* Excluding sales tax (21%)
Parts manufacturer
Reach thousands of remanufacturing companies. Promote your aftermarket parts and services world wide.
Please contact Enginedesk via info@enginedesk.com.
