Technical Data - K.H.D. (410) F 2L410D
Manufacturer K.H.D.
(410) F 2L410D - I -
| Engine Type | (410) F 2L410D |
| Fuel Supply System | I |
| Note |
| Cc | 1270 |
| Number of Cylinders | 2 |
| Bore Ø | 90.00 |
| Stroke | 100.00 |
| KW | 18 |
| Compression |
| KBA No. (Germany) | 4114371 |
| Type Mines | 905A3C |
| Technical Information Number | Technical Data | Information |
|---|---|---|
| Compression-------------- | ||
| ····Compression - Ratio | ||
| ····Compression - Pressure [bar] | ||
| Refs------ | ||
| ····Idle, min. | ||
| ····RPM, Max. | ||
| Oil Pressure------------- | ||
| ····Status (Operating Mode / Cold Check) | ||
| ····Idle, min. | ||
| ····Min. | ||
| ····Rated Capacity | ||
| injection pump----------- | ||
| ··Injection - Stage 1 => x | ||
| ····Injection (Point - ° before TDC) | ||
| ··Pressure, Fuel injection | ||
| ····New Part | ||
| ····Min. | ||
| =<>= | ||
| General Information - Cylinder Head ------------------------- | ||
| ··Cylinder Head - Number | ||
| ··Material, Surface | ||
| ··Cylinder Head - Height | ||
| ····Cylinder Head - Height (D) | ||
| ····Wear limitation | ||
| ··Piston Crown Clearance -/+ | ||
| Valves---- | ||
| ··Valve Clearance [mm] | ||
| ····Operating Mode / Cold Check | ||
| ····Inlet | ||
| ····Inlet | ||
| ····Exhaust | ||
| ····Exhaust | ||
| ··Valve Clearance - Cold Check [mm] | ||
| ····Temp. Range | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Actuation, Setting | ||
| ····Inlet / Open (° before TDC) | ||
| ····Inlet / Closed (° after BDC) | ||
| ····Exhaust / Open (° before BDC) | ||
| ····Exhaust / Closed (° after TDC) | ||
| ··Valve Head Diameter [D] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valves - Length (L) | ||
| ····Inlet - New Part | ||
| ····Exhaust - New Part | ||
| ··Valve lift | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve stem diameter [d] - Inlet | ||
| ····Material | ||
| ····Standard Size | ||
| ··Valve stem diameter [d] - Exhaust | ||
| ····Material | ||
| ····Standard Size | ||
| ··Valve Seat Angle [°] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valves, Fitted Height | ||
| ····Inlet | ||
| ····Standard Size | ||
| ····Wear limitation - Inlet | ||
| ····Exhaust | ||
| ····Standard Size | ||
| ····Wear limitation - Outlet | ||
| Valve Spring------------- | ||
| ··Valve Spring - Length (Load/Empty) | ||
| ····New Part | ||
| ····Wear limitation | ||
| Valve Guides------------- | ||
| ··Material | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Fitting, Temperature Range [°C] | ||
| ··Valve Guide - Length [mm] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Inner Diameter - Standard Size | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Outer Diameter - Standard Size | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Bore - Holder, Valve Guides (Standard Size) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Clearance - Valve => Valve Guides | ||
| ····Inlet | ||
| ····Wear limitation - Inlet | ||
| ····Exhaust | ||
| ····Wear limitation - Outlet | ||
| Valve seat | ||
| ··Valve seat - Width | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Seat Angle (B) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Seat - Measurement (B) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Seat - Outer Diameter, Standard Size | ||
| ····Inlet 1 | ||
| ····Exhaust | ||
| ··Bore - Holder, Valve Seat (Standard Size) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Cylinder Head, Temperature - Press-fitted | ||
| Valve Actuation--------- | ||
| ··Clearance, Radial - Rocker | ||
| ····Inlet | ||
| ····Exhaust | ||
| Camshaft-- | ||
| ··Bearing - Number | ||
| ··Bore - Holder, Camshaft (Bearing Shell) | ||
| ··Clearance, Radial - Camshaft Bushes | ||
| ··Clearance, Radial - Camshaft Bushes | ||
| ····Wear limitation - Inlet | ||
| ··Clearance, Axial - Camshaft Bushes | ||
| ····Wear limitation | ||
| ··Valve lift | ||
| ····Inlet | ||
| ····Exhaust | ||
| =<>= | ||
| General Information - Engine Block | ||
| ··Bore - Holder, Main Bearings (Engine Block) | ||
| ····1st Bearing | ||
| ····2nd Bearing | ||
| ····3rd Bearing | ||
| Cylinder Sleeve---------- | ||
| ··Thickness, Flange (Upper section) | ||
| ··Outer Diameter - Flange, Cylinder Sleeve | ||
| ··Bore | ||
| ····Standard Size | ||
| ····Wear limitation | ||
| ····1st Oversize | ||
| ····2nd Oversize | ||
| ··Adjustment - Machined (Tolerance) | ||
| ····Inner Diameter | ||
| ··Cylinder Sleeve, Length | ||
| ··Inner Diameter - Cylinder Sleeve | ||
| ····Standard Size | ||
| ··Outer Diameter - Cylinder Sleeve | ||
| ····Standard Size | ||
| Piston---- | ||
| ··Length | ||
| ··Compression Height | ||
| ····Possible - Compression Height | ||
| ··Piston Crown Clearance -/+ | ||
| ··Diameter - Piston | ||
| ····Standard Size | ||
| ····Wear limitation | ||
| ····1st Oversize | ||
| ····2nd Oversize | ||
| ··Clearance - Piston | ||
| Gudgeon Pin-------------- | ||
| ··Length [mm] - Gudgeon Pin | ||
| ··Diameter - Gudgeon Pin | ||
| ··Diameter - Gudgeon Pin (Eye) | ||
| ··Clearance, Radial - Gudgeon Pin | ||
| ····Clearance, Radial - Small End Bush / Gudgeon Pin | ||
| Piston Ring Set---------- | ||
| ··Height, 1st Piston Ring (Compression) | ||
| ··Height, 2nd Piston Ring (Compression) | ||
| ··Height, 3rd Piston Ring (Compression) | ||
| ··Height, Piston Ring (Oil Trap) | ||
| ··Piston Ring, Groove | ||
| ··Piston Ring, Compression | ||
| ··1st Piston Ring (Compression) | ||
| ··2nd Piston Ring (Compression) | ||
| ··3rd Piston Ring (Compression) | ||
| ··Piston Ring, Oil Trap | ||
| ··1st Piston Ring, Lock - Clearance (Compression) | ||
| ····Wear limitation | ||
| ··2nd Piston Ring, Lock - Clearance (Compression) | ||
| ····Wear limitation | ||
| ··3rd Piston Ring, Lock - Clearance (Compression) | ||
| ····Wear limitation | ||
| ··Piston Ring, Lock - Clearance (Oil Trap) | ||
| ····Wear limitation | ||
| ··1st Piston Ring, Height - Clearance (Compression) | ||
| ····Wear limitation | ||
| ··2nd Piston Ring, Height - Clearance (Compression) | ||
| ····Wear limitation | ||
| ··3rd Piston Ring, Height - Clearance (Compression) | ||
| ····Wear limitation | ||
| ··Piston Ring, Height - Clearance (Oil Trap) | ||
| ····Wear limitation | ||
| Connecting Rod----------- | ||
| ··Distance, Centre - Small End Bush / Big End Bearing | ||
| ··Bore - Holder, Connecting Rod (Small End Bushes) | ||
| ··Bore - Holder, Connecting Rod (Big End Bearing) | ||
| ····Standard Size | ||
| ··Width, Connecting Rod - Base | ||
| ····Standard Size | ||
| ··Inner Diameter - Big End Bearing | ||
| ····Standard Size | ||
| ····1st Oversize | ||
| ····2nd Oversize | ||
| ····3rd Oversize | ||
| ··Clearance, Radial - Big End Bearing | ||
| ····Wear limitation | ||
| ··Clearance, Axial - Big End Bearing | ||
| ··Diameter, Bearing Journal - Connecting Rod | ||
| ····Standard Size | ||
| ····1st Undersize | ||
| ····2nd Undersize | ||
| ····3rd Undersize | ||
| ····4th Undersize | ||
| ····5th Undersize | ||
| ····6th Undersize | ||
| ··Bearing Journal, Connecting Rod - Tolerance (Oval) | ||
| ····Bearing Journal, Connecting Rod - Oval (Max.) | ||
| ··Big End Bearing, Width | ||
| ··Thickness, Big End Bearings | ||
| ····Standard Size | ||
| ····1st Oversize | ||
| ····2nd Oversize | ||
| ····3rd Undersize | ||
| ··Small End Bushes | ||
| ····Inner Diameter | ||
| ····Wear limitation | ||
| ····Outer Diameter | ||
| ····Length | ||
| ····Clearance, Radial - Small End Bush / Gudgeon Pin | ||
| Crankshaft | ||
| ··Material | ||
| ··Hardened (Tolerance) | ||
| ··Number of bearings | ||
| ··Diameter, Bearing Journal - Crankshaft (Standard Size) | ||
| ··Diameter, Bearing Journal - Crankshaft (1st Undersize) | ||
| ··Diameter, Bearing Journal - Crankshaft (2nd Undersize) | ||
| ··Diameter, Bearing Journal - Crankshaft (3rd Undersize) | ||
| ··Diameter, Bearing Journal - Crankshaft (4th Undersize) | ||
| Main Bearings (Thrust Bearing) | ||
| ····Standard Size | ||
| ····1st Oversize | ||
| ····2nd Oversize | ||
| ····3rd Oversize | ||
| ····4th Oversize | ||
| ··Width, Bearing Journal (Crankshaft) | ||
| ····1st Bearing | ||
| ····2nd Bearing | ||
| ····3rd Bearing | ||
| ··Bearing Journal, Crankshaft - Oval (Max.) | ||
| ····Wear limitation | ||
| ··Outer Diameter - Bolt (Main Bearing Cap) | ||
| ··Clearance - Main Bearing, crankshaft | ||
| ··Clearance - Main Bearing, crankshaft | ||
| ··Bearing clearance - Axial Bearing | ||
| Main Bearing scales, crankshaft ----------------------------- | ||
| ··Inner Diameter - Main Bearings | ||
| ····Standard Size | ||
| ····1st Oversize | ||
| ····2nd Oversize | ||
| ····3rd Undersize | ||
| ··Thickness, Main Bearings, crankshaft | ||
| ····Standard Size | ||
| ····1st Oversize | ||
| ····2nd Undersize | ||
| ····3rd Oversize | ||
| ····4th Oversize | ||
| ··Thickness, Axial Bearing (Bearing Shell) | ||
| ····Standard Size | ||
| ····1st Oversize | ||
| ····2nd Oversize | ||
| ····3rd Oversize | ||
| ····4th Oversize | ||
| Flywheel-- | ||
| ··Vibration Damper | ||
| ····Clearance, Axial (Max.) | ||
| ····Clearance, Radial (Max.) | ||
| Cooling System----------- | ||
| ··Type | ||
| Timing Gear, Kit (Control)- | ||
| ··Clearance, Axial - Gear wheel | ||
| ····Wear limitation | ||
| =<>= | ||
| Cylinder Head Bolts------ | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| ····Stage 3 | ||
| ····Stage 4 | ||
| ····Retouching | ||
| ····Bolt Length - Max. | ||
| Main Bearing Cap, crankshaft -------------------------------- | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| Bearing Cap, connecting rod | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| ····Stage 3 | ||
| Crankshaft | ||
| Stabilizer, Weight - Crankshaft ----------------------------- | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| Flywheel-- | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| ····Stage 3 | ||
| Camshaft, Bearing Cap---- | ||
| ····Camshaft, Bolt | ||
| Rocker Arm Shaft, valve train ------------------------------- | ||
| ··Rocker Arm Bridge | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| ··Rocker | ||
| Injector Nozzle---------- | ||
| ····Injector Holder | ||
| Intake Manifold---------- |
Gain access
Enginedesk contains rich-data for parts and engines. The service is particulary useful for engine rebuilders and maintenance shops.
You can browse all information online. To get access to the technical data and parts information we provide the following options:
- Anytime 'all access' € 25,- * per month.
- Anytime 'all access' € 250,- * yearly.
* Excluding sales tax (21%)
Parts manufacturer
Reach thousands of remanufacturing companies. Promote your aftermarket parts and services world wide.
Please contact Enginedesk via info@enginedesk.com.
