Technical Data - KÄMPER 492 N
Manufacturer KÄMPER
492 N - I -
| Engine Type | 492 N |
| Fuel Supply System | I |
| Note |
| Cc | 3138 |
| Number of Cylinders | 4 |
| Bore Ø | 92.00 |
| Stroke | 118.00 |
| KW | 37 |
| Compression | 19.0 |
| KBA No. (Germany) | 4114371 |
| Type Mines | 905A3C |
| Technical Information Number | Technical Data | Information |
|---|---|---|
| Compression-------------- | ||
| ····Compression - Ratio | ||
| ····Compression - Pressure [bar] | ||
| Refs------ | ||
| ····RPM, Max. | ||
| injection pump----------- | ||
| ··Injection - Stage 1 => x | ||
| ····Injection (Point - ° before TDC) | ||
| ··Pressure, Fuel injection | ||
| ····New Part | ||
| =<>= | ||
| General Information - Cylinder Head ------------------------- | ||
| ··Cylinder Head - Number | ||
| ··Material, Surface | ||
| ··Piston Crown Clearance -/+ | ||
| Valves---- | ||
| ··Valve Clearance [mm] | ||
| ····Operating Mode / Cold Check | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Actuation, Setting | ||
| ····Inlet / Open (° before TDC) | ||
| ····Inlet / Closed (° after BDC) | ||
| ··Valve Head Diameter [D] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valves - Length (L) | ||
| ····Inlet - New Part | ||
| ····Exhaust - New Part | ||
| ··Valve stem diameter [d] - Inlet | ||
| ····Standard Size | ||
| ··Valve stem diameter [d] - Exhaust | ||
| ····Standard Size | ||
| ··Valve Seat Angle [°] | ||
| ····Inlet | ||
| ····Exhaust | ||
| Valve Guides------------- | ||
| ··Clearance - Valve => Valve Guides | ||
| ····Inlet | ||
| ····Exhaust | ||
| Camshaft-- | ||
| ··Bearing - Number | ||
| ··Diameter, Bearing Journal - Camshaft (Standard Size) | ||
| ··Clearance, Radial - Camshaft Bushes | ||
| ··Clearance, Axial - Camshaft Bushes | ||
| =<>= | ||
| General Information - Engine Block | ||
| ··Bore - Holder, Main Bearings (Engine Block) | ||
| Cylinder Sleeve---------- | ||
| ··Seal (Tombak) - Thickness | ||
| ··Thickness, Flange (Upper section) | ||
| ··Outer Diameter - Flange, Cylinder Sleeve | ||
| ··Bore | ||
| ····Standard Size | ||
| ····1st Oversize | ||
| ····2nd Oversize | ||
| ··Cylinder Sleeve, Length | ||
| ··Inner Diameter - Cylinder Sleeve | ||
| ····Standard Size | ||
| ··Outer Diameter - Cylinder Sleeve | ||
| Piston---- | ||
| ··Length | ||
| ··Compression Height | ||
| ····Possible - Compression Height | ||
| ··Piston Crown Clearance -/+ | ||
| ··Diameter - Piston | ||
| ····Standard Size | ||
| ··Clearance - Piston | ||
| Gudgeon Pin-------------- | ||
| ··Length [mm] - Gudgeon Pin | ||
| ··Diameter - Gudgeon Pin | ||
| ··Clearance, Radial - Gudgeon Pin / Piston | ||
| ··Clearance, Radial - Gudgeon Pin | ||
| ····Clearance, Radial - Piston Rod / Piston | ||
| ····Clearance, Radial - Small End Bush / Gudgeon Pin | ||
| Piston Ring Set---------- | ||
| ··Height, 1st Piston Ring (Compression) | ||
| ··Height, 2nd Piston Ring (Compression) | ||
| ··Height, 3rd Piston Ring (Compression) | ||
| ··Height, 1st Piston Ring (Oil Trap) | ||
| ··Height, 2nd Piston Ring (Oil Trap) | ||
| Connecting Rod----------- | ||
| ··Distance, Centre - Small End Bush / Big End Bearing | ||
| ··Bore - Holder, Connecting Rod (Big End Bearing) | ||
| ··Clearance, Radial - Big End Bearing | ||
| ····Wear limitation | ||
| ··Diameter, Bearing Journal - Connecting Rod | ||
| ····Standard Size | ||
| ····1st Undersize | ||
| ··Small End Bushes | ||
| ····Inner Diameter | ||
| ····Clearance, Radial - Small End Bush / Gudgeon Pin | ||
| Crankshaft | ||
| ··Number of bearings | ||
| ··Diameter, Bearing Journal - Crankshaft (Standard Size) | ||
| ··Diameter, Bearing Journal - Crankshaft (1st Undersize) | ||
| ··Clearance - Main Bearing, crankshaft | ||
| ··Bearing clearance - Axial Bearing | ||
| =<>= | ||
| Cylinder Head------------ | ||
| Cylinder Head Bolts------ | ||
| ····Stage 1 | ||
| Main Bearing Cap, crankshaft -------------------------------- | ||
| Bearing Cap, connecting rod | ||
| Flywheel-- | ||
| Injector Nozzle---------- | ||
| ····Injector Holder |
Gain access
Enginedesk contains rich-data for parts and engines. The service is particulary useful for engine rebuilders and maintenance shops.
You can browse all information online. To get access to the technical data and parts information we provide the following options:
- Anytime 'all access' € 25,- * per month.
- Anytime 'all access' € 250,- * yearly.
* Excluding sales tax (21%)
Parts manufacturer
Reach thousands of remanufacturing companies. Promote your aftermarket parts and services world wide.
Please contact Enginedesk via info@enginedesk.com.
