Technical Data - MAZDA E3
Manufacturer MAZDA
E3 - C - SOHC/OHC
| Engine Type | E3 |
| Fuel Supply System | C |
| Note | SOHC/OHC |
| Cc | 1296 |
| Number of Cylinders | 4 |
| Bore Ø | 77.00 |
| Stroke | 69.60 |
| KW | 50 |
| Compression | 9.20 |
| KBA No. (Germany) | 4114371 |
| Type Mines | 905A3C |
| Technical Information Number | Technical Data | Information |
|---|---|---|
| ····Engine Code | ||
| Compression-------------- | ||
| ····Compression - Ratio | ||
| ····Compression - Pressure [bar] | ||
| ····Cylinder - Differential pressure | ||
| ····Wear limitation | ||
| Refs------ | ||
| ····Idle, min. | ||
| ····Automatic Transmission | ||
| Exhaust Gas, value------- | ||
| ····CO Measurement, Idle | ||
| ····CO2 Measurement, Idle [%] | ||
| ····HC Measurement, Idle | ||
| Oil Pressure------------- | ||
| ····Status (Operating Mode / Cold Check) | ||
| ····Rated Capacity | ||
| Thermostat | ||
| ····Thermostat, Opening Temperature | ||
| Ignition Timing---------- | ||
| ····Ignition System | ||
| Ignition - Row----------- | ||
| =<>= | ||
| General Information - Cylinder Head ------------------------- | ||
| ··Cylinder Head - Number | ||
| ··Unleaded - Design | ||
| ··Cylinder Head - Height | ||
| ····New Part | ||
| ····Min. | ||
| ··warpage (value) - Cylinder Head | ||
| Valves---- | ||
| ··Valve Clearance [mm] | ||
| ····Operating Mode / Cold Check | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Actuation, Setting | ||
| ····Inlet / Open (° before TDC) | ||
| ····Inlet / Closed (° after BDC) | ||
| ····Exhaust / Open (° before BDC) | ||
| ····Exhaust / Closed (° after TDC) | ||
| ··Valve Head Diameter [D] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valves - Length (L) | ||
| ····Inlet - New Part | ||
| ····Exhaust - New Part | ||
| ··Valve stem diameter [d] - Inlet | ||
| ····Wear limitation | ||
| ··Valve stem diameter [d] - Exhaust | ||
| ····Wear limitation | ||
| ··Valve Seat Angle [°] | ||
| ··Valve Disc, Thickness (t) | ||
| ··Clearance - Valve Disc => Cylinder Head (Surface) | ||
| ··Clearance - Valve Disc => Cylinder Head (Surface) | ||
| ····Wear limitation - Inlet | ||
| ····Wear limitation - Inlet | ||
| ····Wear limitation - Outlet | ||
| ····Wear limitation - Outlet | ||
| Valve Spring------------- | ||
| ··Tolerance - Vertical (s) | ||
| ··Valve Spring - Length (Load/Empty) | ||
| ····Wear limitation | ||
| ··Diameter - Spring, Material | ||
| Valve Guides------------- | ||
| ··Temperature Range [°C] - Press-out | ||
| ··Valve Guide - Length [mm] | ||
| ··Inner Diameter - Standard Size | ||
| ··Outer Diameter - Standard Size | ||
| ··Clearance - Valve => Valve Guides | ||
| ····Wear limitation - Inlet | ||
| Valve seat | ||
| ··Valve Seat Angle (B) | ||
| ··Adaptation - Angle (B1) | ||
| ··Adaptation - Angle (B2) | ||
| ··Valve Seat - Measurement (A) | ||
| ··Cylinder Head, Temperature - Press-fitted | ||
| Valve Actuation--------- | ||
| ··Rocker Arm Shaft, valve train | ||
| ····Fitting Position | ||
| ··Diameter - Rocker arm shaft | ||
| ··Bore - Holder, Rocker Bush (Rocker) | ||
| ··Clearance, Radial - Rocker | ||
| ····Wear limitation - Outlet | ||
| Camshaft-- | ||
| ··Diameter, Bearing Journal - Camshaft (Standard Size) | ||
| ····1st Bearing | ||
| ····2nd Bearing | ||
| ····3rd Bearing | ||
| ····Wear limitation | ||
| ··Clearance, Radial - Camshaft Bushes | ||
| ····Wear limitation | ||
| ····1st Bearing | ||
| ····2nd Bearing | ||
| ····3rd Bearing | ||
| ··Clearance, Axial - Camshaft Bushes | ||
| ····Wear limitation | ||
| ··Centering - Camshaft (Tolerance) | ||
| ··Cam Lobe Height (Total) | ||
| ····Inlet | ||
| ····Inlet - min. | ||
| ····Exhaust | ||
| ····Exhaust - Min. | ||
| =<>= | ||
| General Information - Engine Block | ||
| Cylinder Sleeve---------- | ||
| ··Bore | ||
| ··Bore | ||
| ····Standard Size | ||
| ····Wear limitation | ||
| ····1st Oversize | ||
| ····2nd Oversize | ||
| Piston---- | ||
| ··Fitting Position | ||
| ····Possible - Compression Height | ||
| ··Diameter - Piston | ||
| ····Standard Size | ||
| ····1st Oversize | ||
| ····2nd Oversize | ||
| Gudgeon Pin-------------- | ||
| ····Press-fitted (Temperature -C°) | ||
| Piston Ring Set---------- | ||
| ··Height, 1st Piston Ring (Compression) | ||
| ··Height, 2nd Piston Ring (Compression) | ||
| ··Height, Piston Ring (Oil Trap) | ||
| ··Piston Ring, Groove | ||
| ··1st Piston Ring, Lock - Clearance (Compression) | ||
| ····Wear limitation | ||
| ··2nd Piston Ring, Lock - Clearance (Compression) | ||
| ····Wear limitation | ||
| ··Piston Ring, Lock - Clearance (Oil Trap) | ||
| ····Wear limitation | ||
| ··1st Piston Ring, Height - Clearance (Compression) | ||
| ····Wear limitation | ||
| ··2nd Piston Ring, Height - Clearance (Compression) | ||
| ····Wear limitation | ||
| ··Piston Ring, Height - Clearance (Oil Trap) | ||
| Connecting Rod----------- | ||
| ··Fitting Position | ||
| ··Distance, Centre - Small End Bush / Big End Bearing | ||
| ··Bore - Holder, Connecting Rod (Small End Bushes) | ||
| ··Bore - Holder, Connecting Rod (Big End Bearing) | ||
| ··Width, Connecting Rod - Base | ||
| ··Clearance, Radial - Big End Bearing | ||
| ····Wear limitation | ||
| ····Wear limitation | ||
| ··Clearance, Axial - Big End Bearing | ||
| ··Diameter, Bearing Journal - Connecting Rod | ||
| ····Standard Size | ||
| ····Wear limitation | ||
| ····1st Undersize | ||
| ····2nd Undersize | ||
| ····3rd Undersize | ||
| ··Bearing Journal, Connecting Rod - Tolerance (Oval) | ||
| ····Bearing Journal, Connecting Rod - Oval (Max.) | ||
| ··Bearing Journal, Connecting Rod - Conical (Max.) | ||
| Crankshaft | ||
| ··Material | ||
| ··Number of bearings | ||
| ··Centering - Crankshaft (Tolerance) | ||
| ··Grindable | ||
| ··Diameter, Bearing Journal - Crankshaft (Standard Size) | ||
| ··Diameter, Bearing Journal - Crankshaft (1st Undersize) | ||
| ··Diameter, Bearing Journal - Crankshaft (2nd Undersize) | ||
| ··Diameter, Bearing Journal - Crankshaft (3rd Undersize) | ||
| ··Bearing Journal, Crankshaft - Conical (Max.) | ||
| ··Clearance - Main Bearing, crankshaft | ||
| ····1st Bearing | ||
| ··Bearing clearance - Axial Bearing | ||
| ····Wear limitation | ||
| Main Bearing scales, crankshaft ----------------------------- | ||
| ··Fitting Position | ||
| ··Thickness, Axial Bearing (Bearing Shell) | ||
| ····Fitting Position | ||
| Cooling System----------- | ||
| Cooling System----------- | ||
| ··Type | ||
| ··Clearance - Outer, Rotor => Inside, Rotor | ||
| ··Clearance - Outer, Rotor => Housing, Oil Pump | ||
| ··Clearance, Axial - Gear wheels => Oil Pump Housing Lid | ||
| =<>= | ||
| Valve Cover-------------- | ||
| Cylinder Head Bolts------ | ||
| Main Bearing Cap, crankshaft -------------------------------- | ||
| Bearing Cap, connecting rod | ||
| Crankshaft | ||
| Crankshaft Gear---------- | ||
| Flywheel-- | ||
| Camshaft-- | ||
| ··Adjusting Screw, valve clearance, Lock Screw | ||
| Camshaft, Bearing Cap---- | ||
| Rocker Arm Shaft, valve train ------------------------------- | ||
| ··Rocker Arm Bridge | ||
| Drive gear - Camshaft---- | ||
| Timing Case-------------- | ||
| ··Timing Case, Cover | ||
| ··Timing Chain Tensioner | ||
| ····Chain Tensioner | ||
| Alternator | ||
| Spark Plug | ||
| Starter--- | ||
| Water Pump | ||
| Oil Pump-- | ||
| Oil Pan--- | ||
| ··Oil Drain Plug, oil pan | ||
| Exhaust Manifold--------- | ||
| Intake Manifold---------- | ||
| Intake Manifold---------- |
Gain access
Enginedesk contains rich-data for parts and engines. The service is particulary useful for engine rebuilders and maintenance shops.
You can browse all information online. To get access to the technical data and parts information we provide the following options:
- Anytime 'all access' € 25,- * per month.
- Anytime 'all access' € 250,- * yearly.
* Excluding sales tax (21%)
Parts manufacturer
Reach thousands of remanufacturing companies. Promote your aftermarket parts and services world wide.
Please contact Enginedesk via info@enginedesk.com.
