Technical Data - M.W.M. D 232-12
Manufacturer M.W.M.
D 232-12 - I - V -engine
| Engine Type | D 232-12 |
| Fuel Supply System | I |
| Note | V -engine |
| Cc | 17640 |
| Number of Cylinders | 12 |
| Bore Ø | 120.00 |
| Stroke | 130.00 |
| KW | 243 |
| Compression | 16.5 |
| KBA No. (Germany) | 4114371 |
| Type Mines | 905A3C |
| Technical Information Number | Technical Data | Information |
|---|---|---|
| Compression-------------- | ||
| ····Compression - Ratio | ||
| ····Compression - Pressure [bar] | ||
| ····Wear limitation | ||
| Refs------ | ||
| ····Idle, min. | ||
| ····RPM, Max. | ||
| Oil Pressure------------- | ||
| ····Status (Operating Mode / Cold Check) | ||
| ····Idle, min. | ||
| ····Rated Capacity | ||
| injection pump----------- | ||
| ··Injection - Stage 1 => x | ||
| ··Injection - Stage 1 => x | ||
| ··Pressure, Fuel injection | ||
| =<>= | ||
| Valves---- | ||
| ··Valve Clearance [mm] | ||
| ····Operating Mode / Cold Check | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Actuation, Setting | ||
| ····Inlet / Open (° before TDC) | ||
| ····Inlet / Closed (° after BDC) | ||
| ····Exhaust / Open (° before BDC) | ||
| ····Exhaust / Closed (° after TDC) | ||
| ··Valve stem diameter [d] - Inlet | ||
| ····Standard Size | ||
| ····Wear limitation | ||
| ··Valve stem diameter [d] - Exhaust | ||
| ····Standard Size | ||
| ····Wear limitation | ||
| ··Valve - Protrusion (+/-) | ||
| ····Wear limitation - Inlet | ||
| Valve Guides------------- | ||
| ··Valve Guide - Length [mm] | ||
| ··Inner Diameter - Standard Size | ||
| ··Inner Diameter - Standard Size | ||
| ····Wear limitation - Inlet | ||
| Valve seat | ||
| ··Valve Seat - Measurement (A) | ||
| ····Wear limitation | ||
| Valve Actuation--------- | ||
| ··Diameter - Rocker arm shaft | ||
| ····Wear limitation | ||
| ··Inner Diameter - Rocker arm shaft (Bearing Bush) | ||
| ····Wear limitation | ||
| Valve Lifter------------- | ||
| ··Diameter - Valve Lifter | ||
| ····Standard Size | ||
| ····Wear limitation | ||
| ··Bore - Holder, Rocker/ Tappet | ||
| ····Standard Size | ||
| ····Wear limitation | ||
| Camshaft-- | ||
| ··Bore - Holder, Camshaft Bushes (Standard Size) | ||
| ····Wear limitation | ||
| ··Diameter, Bearing Journal - Camshaft (Standard Size) | ||
| ····Wear limitation | ||
| ··Diameter, Bearing Journal - Camshaft (Undersize) | ||
| ··Clearance, Axial - Camshaft Bushes | ||
| ····Wear limitation | ||
| =<>= | ||
| Cylinder Sleeve---------- | ||
| ··Inner Diameter - Cylinder Sleeve | ||
| ····Standard Size | ||
| ····Wear limitation | ||
| Piston---- | ||
| ··Diameter - Piston | ||
| ····Standard Size | ||
| ····Wear limitation | ||
| Gudgeon Pin-------------- | ||
| ··Diameter - Gudgeon Pin | ||
| ····Wear limitation | ||
| Piston Ring Set---------- | ||
| ··Piston Ring, Groove | ||
| ··1st Piston Ring (Compression) | ||
| ··2nd Piston Ring (Compression) | ||
| ··Piston Ring, Oil Trap | ||
| ··1st Piston Ring, Lock - Clearance (Compression) | ||
| ····Wear limitation | ||
| ··2nd Piston Ring, Lock - Clearance (Compression) | ||
| ····Wear limitation | ||
| ··Piston Ring, Lock - Clearance (Oil Trap) | ||
| ····Wear limitation | ||
| ··1st Piston Ring, Height - Clearance (Compression) | ||
| ····Wear limitation | ||
| ··2nd Piston Ring, Height - Clearance (Compression) | ||
| ····Wear limitation | ||
| ··Piston Ring, Height - Clearance (Oil Trap) | ||
| ····Wear limitation | ||
| Connecting Rod----------- | ||
| ··Bore - Holder, Connecting Rod (Small End Bushes) | ||
| ··Bore - Holder, Connecting Rod (Big End Bearing) | ||
| ··Diameter, Bearing Journal - Connecting Rod | ||
| ····Standard Size | ||
| ····Wear limitation | ||
| ····1st Undersize | ||
| ····2nd Undersize | ||
| ····3rd Undersize | ||
| ····4th Undersize | ||
| ··Big End Bearing, Width | ||
| ··Small End Bushes | ||
| ····Wear limitation | ||
| Crankshaft | ||
| ··Diameter, Bearing Journal - Crankshaft (Standard Size) | ||
| ··Diameter, Bearing Journal - Crankshaft (Standard Size) | ||
| ··Diameter, Bearing Journal - Crankshaft (Standard Size) | ||
| ····2 - 7. Bearing | ||
| ··Diameter, Bearing Journal - Crankshaft (1st Undersize) | ||
| ··Diameter, Bearing Journal - Crankshaft (2nd Undersize) | ||
| ··Diameter, Bearing Journal - Crankshaft (3rd Undersize) | ||
| ··Diameter, Bearing Journal - Crankshaft (4th Undersize) | ||
| ··Width, Bearing Journal (Crankshaft) | ||
| ··Bearing clearance - Axial Bearing | ||
| ····Wear limitation | ||
| Balance Shaft------------ | ||
| ··Diameter, Bearing Journal - Balancer Shaft (Standard Size) | ||
| ····Wear limitation - Bearing 1 | ||
| ··Inner Diameter - Bearing, balance shaft (Standard Size) | ||
| ····Wear limitation | ||
| =<>= |
Gain access
Enginedesk contains rich-data for parts and engines. The service is particulary useful for engine rebuilders and maintenance shops.
You can browse all information online. To get access to the technical data and parts information we provide the following options:
- Anytime 'all access' € 25,- * per month.
- Anytime 'all access' € 250,- * yearly.
* Excluding sales tax (21%)
Parts manufacturer
Reach thousands of remanufacturing companies. Promote your aftermarket parts and services world wide.
Please contact Enginedesk via info@enginedesk.com.
