Technical Data - M.W.M. KD 11- 1 (E)
Manufacturer M.W.M.
KD 11- 1 (E) - I -
| Engine Type | KD 11- 1 (E) |
| Fuel Supply System | I |
| Note |
| Cc | 625 |
| Number of Cylinders | 1 |
| Bore Ø | 85.00 |
| Stroke | 110.00 |
| KW | 4.5 |
| Compression | 18 |
| KBA No. (Germany) | 4114371 |
| Type Mines | 905A3C |
| Technical Information Number | Technical Data | Information |
|---|---|---|
| Compression-------------- | ||
| ····Compression - Ratio | ||
| ····Compression - Pressure [bar] | ||
| ····Wear limitation | ||
| Refs------ | ||
| ····Idle, min. | ||
| ····RPM, Max. | ||
| Oil Pressure------------- | ||
| ····Status (Operating Mode / Cold Check) | ||
| ····Idle, min. | ||
| ····Min. | ||
| ····Rated Capacity | ||
| injection pump----------- | ||
| ··Injection - Stage 1 => x | ||
| ····Injection (Point - ° before TDC) | ||
| ··Pressure, Fuel injection | ||
| ····New Part | ||
| =<>= | ||
| General Information - Cylinder Head ------------------------- | ||
| ··Cylinder Head - Number | ||
| ··Piston Crown Clearance -/+ | ||
| ··Piston Crown Clearance -/+ | ||
| Valves---- | ||
| ··Valve Clearance [mm] | ||
| ····Operating Mode / Cold Check | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Actuation, Setting | ||
| ····Inlet / Open (° before TDC) | ||
| ····Inlet / Closed (° after BDC) | ||
| ····Exhaust / Open (° before BDC) | ||
| ····Exhaust / Closed (° after TDC) | ||
| ··Valve Head Diameter [D] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valves - Length (L) | ||
| ····Inlet - New Part | ||
| ····Exhaust - New Part | ||
| ··Valve stem diameter [d] - Inlet | ||
| ····Material | ||
| ····Standard Size | ||
| ··Valve stem diameter [d] - Exhaust | ||
| ····Material | ||
| ····Standard Size | ||
| ··Valve Seat Angle [°] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valves, Fitted Height | ||
| ····Standard Size | ||
| Valve Guides------------- | ||
| ··Material | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Guide - Length [mm] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Inner Diameter - Standard Size | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Outer Diameter - Standard Size | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Clearance - Valve => Valve Guides | ||
| ····Inlet | ||
| ····Exhaust | ||
| Valve seat | ||
| ··Valve Seat Angle (B) | ||
| ····Inlet | ||
| ····Exhaust | ||
| =<>= | ||
| General Information - Engine Block | ||
| ··Bore - Holder, Main Bearings (Engine Block) | ||
| ··Cylinder Sleeve Protrusion | ||
| Cylinder Sleeve---------- | ||
| ··Seal (Tombak) - Thickness | ||
| ··Thickness, Flange (Upper section) | ||
| ··Outer Diameter - Flange, Cylinder Sleeve | ||
| ··Bore | ||
| ····Standard Size | ||
| ····1st Oversize | ||
| ····2nd Oversize | ||
| ··Cylinder Sleeve, Length | ||
| ··Inner Diameter - Cylinder Sleeve | ||
| ····Standard Size | ||
| ··Outer Diameter - Cylinder Sleeve | ||
| ····Standard Size | ||
| Piston---- | ||
| ··Length | ||
| ··Compression Height | ||
| ····Possible - Compression Height | ||
| ··Piston Crown Clearance -/+ | ||
| ··Piston Crown Clearance -/+ | ||
| ··Diameter - Piston | ||
| ····Standard Size | ||
| ····1st Oversize | ||
| ····2nd Oversize | ||
| ··Clearance - Piston | ||
| Gudgeon Pin-------------- | ||
| ··Length [mm] - Gudgeon Pin | ||
| ··Diameter - Gudgeon Pin | ||
| ··Clearance, Radial - Gudgeon Pin | ||
| ····Clearance, Radial - Small End Bush / Gudgeon Pin | ||
| Piston Ring Set---------- | ||
| ··Height, 1st Piston Ring (Compression) | ||
| ··Height, 2nd Piston Ring (Compression) | ||
| ··Height, 3rd Piston Ring (Compression) | ||
| ··Height, 1st Piston Ring (Oil Trap) | ||
| ··Height, 2nd Piston Ring (Oil Trap) | ||
| Connecting Rod----------- | ||
| ··Distance, Centre - Small End Bush / Big End Bearing | ||
| ··Bore - Holder, Connecting Rod (Small End Bushes) | ||
| ··Bore - Holder, Connecting Rod (Big End Bearing) | ||
| ··Clearance, Radial - Big End Bearing | ||
| ····Wear limitation | ||
| ··Diameter, Bearing Journal - Connecting Rod | ||
| ····Standard Size | ||
| ··Small End Bushes | ||
| ····Inner Diameter | ||
| ····Outer Diameter | ||
| ····Length | ||
| Crankshaft | ||
| ··Hardened (Tolerance) | ||
| ··Number of bearings | ||
| ··Diameter, Bearing Journal - Crankshaft (Standard Size) | ||
| ··Clearance - Main Bearing, crankshaft | ||
| ··Bearing clearance - Axial Bearing | ||
| =<>= | ||
| Cylinder Head------------ | ||
| Cylinder Head Bolts------ | ||
| ····Stage 1 | ||
| Main Bearing Cap, crankshaft -------------------------------- | ||
| Bearing Cap, connecting rod | ||
| Crankshaft | ||
| Stabilizer, Weight - Crankshaft ----------------------------- | ||
| Flywheel-- | ||
| Injector Nozzle---------- | ||
| ····Injector Holder |
Gain access
Enginedesk contains rich-data for parts and engines. The service is particulary useful for engine rebuilders and maintenance shops.
You can browse all information online. To get access to the technical data and parts information we provide the following options:
- Anytime 'all access' € 25,- * per month.
- Anytime 'all access' € 250,- * yearly.
* Excluding sales tax (21%)
Parts manufacturer
Reach thousands of remanufacturing companies. Promote your aftermarket parts and services world wide.
Please contact Enginedesk via info@enginedesk.com.
