Technical Data - NISSAN QG15DE
Manufacturer NISSAN
QG15DE - I - DOHC
| Engine Type | QG15DE |
| Fuel Supply System | I |
| Note | DOHC |
| Cc | 1498 |
| Number of Cylinders | 4 |
| Bore Ø | 73.60 |
| Stroke | 88.00 |
| KW | 66 |
| Compression | 9.9 |
| KBA No. (Germany) | 4114371 |
| Type Mines | 905A3C |
| Technical Information Number | Technical Data | Information |
|---|---|---|
| Engine - Manufacturer---- | ||
| ····Construction Year (From - To) | ||
| ····Engine Output kW [HP] | ||
| ····Number of Cylinders | ||
| ····Engine Code | ||
| ····Engine Code | ||
| ····Displacement (exact) [cc] | ||
| Compression-------------- | ||
| ····Compression - Ratio | ||
| ····Compression - Pressure [bar] | ||
| ····Cylinder - Differential pressure | ||
| ····Wear limitation | ||
| Refs------ | ||
| ····Manual Transmission | ||
| ····Automatic Transmission | ||
| Exhaust Gas, value------- | ||
| ····Idle | ||
| ····CO Measurement, Idle | ||
| ····CO Measurement (Catalytic Converter => ) | ||
| ····Oil Temperature (CO Measurement) - °C | ||
| ····HC Measurement, Idle | ||
| ····Idle RPM Increase | ||
| ····CO Measurement, Idle RPM Increase | ||
| ····Lambda Value, Idle RPM Increase | ||
| Oil Pressure------------- | ||
| Oil Pressure------------- | ||
| Oil Pressure------------- | ||
| Oil Pressure------------- | ||
| Oil Pressure------------- | ||
| Oil Pressure------------- | ||
| Thermostat | ||
| ····Thermostat, Opening Temperature | ||
| ····Thermostat, Opening (bar / °C) | ||
| Spark Plug | ||
| ····Electrode Gap [mm] | ||
| ··Type | ||
| Fuel Supply-------------- | ||
| ··Type | ||
| ····Fuel Supply System | ||
| ····Air Flow Sensor | ||
| Feed pump - Fuel--------- | ||
| ····Fuel Pressure (system) | ||
| ····Control Valve, fuel pressure (Pressure / Vacuum) | ||
| Ignition Timing---------- | ||
| ····Ignition System | ||
| ····Pulse Generator | ||
| Ignition - Row----------- | ||
| ····Ignition Point (° before TDC) | ||
| ····premature ignition [degree] / RPM | ||
| =<>= | ||
| ··Cylinder Head - Height | ||
| ····New Part | ||
| ··warpage (value) - Cylinder Head | ||
| ····Standard Size | ||
| ····Wear limitation | ||
| Valves---- | ||
| ··Valve Clearance [mm] | ||
| ····Operating Mode / Cold Check | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Clearance - Cold Check [mm] | ||
| ····Temp. Range | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Actuation, Setting | ||
| ····Inlet / Open (° before TDC) | ||
| ····Inlet / Closed (° after BDC) | ||
| ····Exhaust / Open (° before BDC) | ||
| ····Exhaust / Closed (° after TDC) | ||
| ··Valve Head Diameter [D] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valves - Length (L) | ||
| ····Inlet - New Part | ||
| ····Exhaust - New Part | ||
| ··Valve stem diameter [d] - Inlet | ||
| ··Valve stem diameter [d] - Exhaust | ||
| ····Measurement Range (Max.) - Machined | ||
| ··Valve Seat Angle [°] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Disc, Thickness (t) | ||
| ····Wear limitation - Inlet | ||
| ··Valve - Protrusion (+/-) | ||
| ····Fitting Position | ||
| ····Inlet | ||
| ····Exhaust | ||
| Valve Spring------------- | ||
| ··Tolerance - Vertical (s) | ||
| ··Valve Spring - Length (Load/Empty) | ||
| ··Valve Spring - Length (Load/Empty) | ||
| ··Diameter - Spring, Material | ||
| ··Capacitive Load => Length 1 [mm] | ||
| ··Capacitive Load => Length 1 [mm] | ||
| ····Wear limitation | ||
| ····Wear limitation | ||
| Valve Guides------------- | ||
| ··Fitted Height | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Inner Diameter - Standard Size | ||
| ··Outer Diameter - Standard Size | ||
| ··Outer Diameter - 1st Oversize | ||
| ··Bore - Holder, Valve Guides (Standard Size) | ||
| ··Bore - Holder, Valve Guides (1st Oversize) | ||
| ··Clearance - Valve => Valve Guides | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Sideplay | ||
| ··Press-fitted, Valve Guides | ||
| ····Oversize | ||
| Valve seat | ||
| ··Valve Seat Angle (B) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Adaptation - Angle (B1) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Adaptation - Angle (B2) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Seat - Measurement (A) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Seat - Outer Diameter, 1st Oversize | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Bore - Holder, Valve Seat (Standard Size) | ||
| Valve Lifter------------- | ||
| ··Diameter - Valve Lifter | ||
| ··Bore - Holder, Rocker/ Tappet | ||
| ··Clearance, Radial - Valve Lifter | ||
| Camshaft-- | ||
| ··Bore - Holder, Camshaft Bushes (Standard Size) | ||
| ··Bore - Holder, Camshaft Bushes (Standard Size) | ||
| ··Diameter, Bearing Journal - Camshaft (Standard Size) | ||
| ··Diameter, Bearing Journal - Camshaft (Standard Size) | ||
| ··Clearance, Radial - Camshaft Bushes | ||
| ····Wear limitation | ||
| ··Clearance, Axial - Camshaft Bushes | ||
| ····Wear limitation | ||
| ··Centering - Camshaft (Tolerance) | ||
| ····Wear limitation | ||
| ··Cam Lobe Height (Total) | ||
| ····Inlet | ||
| ····Inlet | ||
| ····Exhaust | ||
| ····Wear limitation | ||
| =<>= | ||
| General Information - Engine Block | ||
| ··Engine Block - Height | ||
| ····New Part | ||
| ··warpage (value) - Cylinder Head | ||
| ····Wear limitation | ||
| Cylinder Sleeve---------- | ||
| ··Bore | ||
| ··Bore | ||
| ····Standard Size | ||
| ····Standard Size | ||
| ····Standard Size | ||
| ··Measurement - Oval, Bore (Cylinder Sleeve) | ||
| ····Standard Size | ||
| ··Measurement - Conical | ||
| ····Standard Size | ||
| ··Inner Diameter - different (Cylinder Sleeve) | ||
| ····Wear limitation | ||
| Piston---- | ||
| ··Diameter - Piston | ||
| ····Standard Size | ||
| ····Standard Size | ||
| ····Standard Size | ||
| ····1st Oversize | ||
| ····2nd Oversize | ||
| ····Measurement (Position) | ||
| ··Clearance - Piston | ||
| Gudgeon Pin-------------- | ||
| ··Diameter - Gudgeon Pin | ||
| ··Diameter - Gudgeon Pin (Eye) | ||
| ··Clearance, Radial - Gudgeon Pin | ||
| ····Clearance, Radial - Piston Rod / Piston | ||
| Piston Ring Set---------- | ||
| ··Piston Ring, Groove | ||
| ··1st Piston Ring, Lock - Clearance (Compression) | ||
| ····Wear limitation | ||
| ··2nd Piston Ring, Lock - Clearance (Compression) | ||
| ····Wear limitation | ||
| ··Piston Ring, Lock - Clearance (Oil Trap) | ||
| ····Wear limitation | ||
| ··1st Piston Ring, Height - Clearance (Compression) | ||
| ····Wear limitation | ||
| ··2nd Piston Ring, Height - Clearance (Compression) | ||
| ····Wear limitation | ||
| ··Piston Ring, Height - Clearance (Oil Trap) | ||
| Connecting Rod----------- | ||
| ··Bending radius | ||
| ····Wear limitation | ||
| ··Twist | ||
| ····Wear limitation | ||
| ··Distance, Centre - Small End Bush / Big End Bearing | ||
| ··Bore - Holder, Connecting Rod (Big End Bearing) | ||
| ··Clearance, Radial - Big End Bearing | ||
| ····Wear limitation | ||
| ····Wear limitation | ||
| ····Wear limitation | ||
| ··Clearance, Axial - Big End Bearing | ||
| ··Diameter, Bearing Journal - Connecting Rod | ||
| ··Diameter, Bearing Journal - Connecting Rod | ||
| ··Diameter, Bearing Journal - Connecting Rod | ||
| ··Diameter, Bearing Journal - Connecting Rod | ||
| ··Bearing Journal, Connecting Rod - Tolerance (Oval) | ||
| ····Bearing Journal, Connecting Rod - Oval (Max.) | ||
| ··Bearing Journal, Connecting Rod - Conical (Max.) | ||
| ··Thickness, Big End Bearings | ||
| ··Thickness, Big End Bearings | ||
| ··Thickness, Big End Bearings | ||
| ··Thickness, Big End Bearings | ||
| ····1st Oversize | ||
| ····2nd Oversize | ||
| ····3rd Undersize | ||
| ··Small End Bushes | ||
| ····Inner Diameter | ||
| Crankshaft | ||
| ··Number of bearings | ||
| ··Centering - Crankshaft (Tolerance) | ||
| ····Measurement - Oval, Max. (Gear, crankshaft) | ||
| ····Crankshaft, Radius [R] | ||
| ··Diameter, Bearing Journal - Crankshaft (Standard Size) | ||
| ··Diameter, Bearing Journal - Crankshaft (Standard Size) | ||
| ··Diameter, Bearing Journal - Crankshaft (Standard Size) | ||
| ··Bearing Journal, Crankshaft - Conical (Max.) | ||
| ····Wear limitation | ||
| ··Bearing Journal, Crankshaft - Oval (Max.) | ||
| ··Clearance - Main Bearing, crankshaft | ||
| ··Clearance - Main Bearing, crankshaft | ||
| ····Wear limitation | ||
| ··Bearing clearance - Axial Bearing | ||
| ····Wear limitation | ||
| Main Bearing scales, crankshaft ----------------------------- | ||
| ··Thickness, Main Bearings, crankshaft | ||
| ··Thickness, Main Bearings, crankshaft | ||
| ··Thickness, Main Bearings, crankshaft | ||
| ··Thickness, Main Bearings, crankshaft | ||
| ··Thickness, Main Bearings, crankshaft | ||
| ····1st Oversize | ||
| ····2nd Undersize | ||
| Flywheel-- | ||
| ··Centering - Flywheel (Tolerance) | ||
| Cooling System----------- | ||
| ··Clearance, Axial - Outer, Rotor (Housing, Oil Pump) | ||
| ··Clearance - Outer, Rotor => Inside, Rotor | ||
| ··Clearance - Outer, Rotor => Housing, Oil Pump | ||
| ··Clearance - inner, Rotor => Housing, Oil Pump | ||
| ··Clearance - inner, Rotor => Housing, Oil Pump | ||
| ··Clearance - Control Valve => Cover | ||
| ··Clearance - Control Valve => Cover | ||
| =<>= | ||
| Valve Cover-------------- | ||
| Cylinder Head------------ | ||
| Cylinder Head Bolts------ | ||
| ····Replace - Bolts | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| ····Release | ||
| ····Stage 4 | ||
| ····Stage 5 | ||
| ····Other - Bolt | ||
| Main Bearing Cap, crankshaft -------------------------------- | ||
| ····Replace - Bolts | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| Bearing Cap, connecting rod | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| Crankshaft | ||
| Cranskhaft Pulley-------- | ||
| ··Knock Sensor | ||
| Flywheel-- | ||
| Driver Plate------------- | ||
| Camshaft, Bearing Cap---- | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| ····Stage 3 | ||
| ····Stage 4 | ||
| Drive gear - Camshaft---- | ||
| ····Inlet | ||
| ····Exhaust | ||
| Spark Plug | ||
| Water Pump | ||
| Cooling System----------- | ||
| ··Radiator Drain Plug | ||
| Oil Pan--- | ||
| ····Bolt | ||
| ··Oil Drain Plug, oil pan | ||
| Exhaust Manifold--------- | ||
| ··Lambda Sensor | ||
| Intake Manifold---------- | ||
| Clutch Pressure Plate---- |
Gain access
Enginedesk contains rich-data for parts and engines. The service is particulary useful for engine rebuilders and maintenance shops.
You can browse all information online. To get access to the technical data and parts information we provide the following options:
- Anytime 'all access' € 25,- * per month.
- Anytime 'all access' € 250,- * yearly.
* Excluding sales tax (21%)
Parts manufacturer
Reach thousands of remanufacturing companies. Promote your aftermarket parts and services world wide.
Please contact Enginedesk via info@enginedesk.com.
