Technical Data - NISSAN SD33 EBRO
Manufacturer NISSAN
SD33 EBRO - I -
| Engine Type | SD33 EBRO |
| Fuel Supply System | I |
| Note |
| Cc | 3246 |
| Number of Cylinders | 6 |
| Bore Ø | 83.00 |
| Stroke | 100.00 |
| KW | 70 |
| Compression | 20.8 |
| KBA No. (Germany) | 4114371 |
| Type Mines | 905A3C |
| Technical Information Number | Technical Data | Information |
|---|---|---|
| Engine - Manufacturer---- | ||
| ····Engine Output kW [HP] | ||
| ····Engine Code | ||
| Compression-------------- | ||
| ····Compression - Ratio | ||
| ····Compression - Pressure [bar] | ||
| Refs------ | ||
| ····Idle, min. | ||
| ····Idle, Max. | ||
| ····RPM, Max. | ||
| Exhaust Gas, value------- | ||
| ····Smoke Grey - Service RPM | ||
| Oil Pressure------------- | ||
| ····Min. | ||
| ····Rated Capacity | ||
| Ignition Timing---------- | ||
| ····Ignition System | ||
| Ignition - Row----------- | ||
| ····premature ignition [degree] / RPM | ||
| injection pump----------- | ||
| ··Pressure, Fuel injection | ||
| ····New Part | ||
| ····Min. | ||
| =<>= | ||
| ··warpage (value) - Cylinder Head | ||
| ····Standard Size | ||
| ····Wear limitation | ||
| Valves---- | ||
| ··Valve Clearance [mm] | ||
| ····Operating Mode / Cold Check | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Head Diameter [D] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valves - Length (L) | ||
| ··Valve stem diameter [d] - Inlet | ||
| ····Standard Size | ||
| ····1st Oversize | ||
| ····2nd Oversize | ||
| ··Valve stem diameter [d] - Exhaust | ||
| ····Standard Size | ||
| ····1st Oversize | ||
| ····2nd Oversize | ||
| ··Valve Seat Angle [°] | ||
| ··Valve Disc, Thickness (t) | ||
| ····Wear limitation - Inlet | ||
| Valve Spring------------- | ||
| ··Tolerance - Vertical (s) | ||
| ··Valve Spring - Length (Load/Empty) | ||
| ··Valve Spring - Length (Load/Empty) | ||
| ··Valve Spring - Length (Load/Empty) | ||
| ··Diameter - Spring, Material | ||
| ··Min. Length [mm] => Capacitive Load 1 | ||
| ··Min. Length [mm] => Capacitive Load 2 | ||
| Valve Guides------------- | ||
| ··Inner Diameter - Standard Size | ||
| ··Clearance - Valve => Valve Guides | ||
| ····Inlet | ||
| ····Wear limitation - Inlet | ||
| ····Exhaust | ||
| ····Wear limitation - Outlet | ||
| Valve seat | ||
| ··Valve Seat Angle (B) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Seat - Diameter (D) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Seat - Diameter (D2) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Seat - Outer Diameter, Standard Size | ||
| ····Inlet 1 | ||
| ····Exhaust | ||
| ··Bore - Holder, Valve Seat (Standard Size) | ||
| ····Exhaust | ||
| ··Bore - Holder, Valve Seat (1st Oversize) | ||
| ····Exhaust | ||
| ··Bore - Holder, Valve Seat (2nd Oversize) | ||
| ····Exhaust | ||
| Camshaft-- | ||
| ··Diameter, Bearing Journal - Camshaft (Standard Size) | ||
| ····1st Bearing | ||
| ····2nd Bearing | ||
| ····3rd Bearing | ||
| ··Clearance, Radial - Camshaft Bushes | ||
| ····Wear limitation | ||
| ····1st Bearing | ||
| ····2nd Bearing | ||
| ····3rd Bearing | ||
| ··Clearance, Axial - Camshaft Bushes | ||
| ····Wear limitation | ||
| ··Centering - Camshaft (Tolerance) | ||
| ····Wear limitation | ||
| ··Cam Lobe Height (Total) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ····Wear limitation | ||
| =<>= | ||
| General Information - Engine Block | ||
| ··Engine Block - Height | ||
| ··Cylinder Sleeve Protrusion | ||
| ····Height - Cylinder Sleeve (different) | ||
| Cylinder Sleeve---------- | ||
| Cylinder Sleeve---------- | ||
| ··Measurement - Oval, Bore (Cylinder Sleeve) | ||
| ····Standard Size | ||
| ····Wear limitation | ||
| ··Measurement - Conical | ||
| ····Standard Size | ||
| ····Wear limitation | ||
| ··Inner Diameter - Cylinder Sleeve | ||
| ····Standard Size | ||
| ····1st Oversize | ||
| Piston---- | ||
| ··Diameter - Piston | ||
| ··Diameter - Piston | ||
| ··Diameter - Piston | ||
| ····Measurement (Position) | ||
| ····Measurement (Position) | ||
| ····Measurement (Position) | ||
| ····Measurement (Position) | ||
| Gudgeon Pin-------------- | ||
| ··Diameter - Gudgeon Pin (Eye) | ||
| ··Clearance, Radial - Gudgeon Pin | ||
| ····Clearance, Radial - Piston Rod / Piston | ||
| Piston Ring Set---------- | ||
| ··Piston Ring, Groove | ||
| ··1st Piston Ring, Lock - Clearance (Compression) | ||
| ····Wear limitation | ||
| ··2nd Piston Ring, Lock - Clearance (Compression) | ||
| ····Wear limitation | ||
| ··3rd Piston Ring, Lock - Clearance (Compression) | ||
| ····Wear limitation | ||
| ··Piston Ring, Lock - Clearance (Oil Trap) | ||
| ····Wear limitation | ||
| ··1st Piston Ring, Height - Clearance (Compression) | ||
| ····Wear limitation | ||
| ··2nd Piston Ring, Height - Clearance (Compression) | ||
| ····Wear limitation | ||
| ··3rd Piston Ring, Height - Clearance (Compression) | ||
| ····Wear limitation | ||
| ··Piston Ring, Height - Clearance (Oil Trap) | ||
| ····Wear limitation | ||
| Connecting Rod----------- | ||
| ··Distance, Centre - Small End Bush / Big End Bearing | ||
| ··Bore - Holder, Connecting Rod (Small End Bushes) | ||
| ··Clearance, Radial - Big End Bearing | ||
| ····Wear limitation | ||
| ····Wear limitation | ||
| ··Clearance, Axial - Big End Bearing | ||
| ··Diameter, Bearing Journal - Connecting Rod | ||
| ····Standard Size | ||
| ····1st Undersize | ||
| ····2nd Undersize | ||
| ····3rd Undersize | ||
| ····4th Undersize | ||
| ··Bearing Journal, Connecting Rod - Tolerance (Oval) | ||
| ····Bearing Journal, Connecting Rod - Oval (Max.) | ||
| ····Wear limitation | ||
| ··Bearing Journal, Connecting Rod - Conical (Max.) | ||
| ····Wear limitation | ||
| Crankshaft | ||
| ··Number of bearings | ||
| ··Centering - Crankshaft (Tolerance) | ||
| ····Wear limitation | ||
| ··Diameter, Bearing Journal - Crankshaft (Standard Size) | ||
| ··Diameter, Bearing Journal - Crankshaft (1st Undersize) | ||
| ··Diameter, Bearing Journal - Crankshaft (2nd Undersize) | ||
| ··Diameter, Bearing Journal - Crankshaft (3rd Undersize) | ||
| ··Diameter, Bearing Journal - Crankshaft (4th Undersize) | ||
| ··Bearing Journal, Crankshaft - Conical (Max.) | ||
| ····Wear limitation | ||
| ··Bearing Journal, Crankshaft - Oval (Max.) | ||
| ····Wear limitation | ||
| ··Clearance - Main Bearing, crankshaft | ||
| ··Clearance - Main Bearing, crankshaft | ||
| ··Clearance - Main Bearing, crankshaft | ||
| ····Wear limitation | ||
| ··Bearing clearance - Axial Bearing | ||
| ····Wear limitation | ||
| =<>= | ||
| Valve Cover-------------- | ||
| Cylinder Head Bolts------ | ||
| Cylinder Head Bolts------ | ||
| Main Bearing Cap, crankshaft -------------------------------- | ||
| Bearing Cap, connecting rod | ||
| Crankshaft | ||
| Crankshaft Gear---------- | ||
| Flywheel-- | ||
| Flywheel-- | ||
| Flywheel-- | ||
| Flywheel-- | ||
| Rocker Arm Shaft, valve train ------------------------------- | ||
| ··Rocker Arm Bridge | ||
| Drive gear - Camshaft---- | ||
| Timing Case-------------- | ||
| ··Timing Case, Cover | ||
| Alternator | ||
| Glow Plug- | ||
| Water Pump | ||
| Cooling System----------- | ||
| ··Radiator Drain Plug | ||
| injection pump----------- | ||
| ··Injection Pipe | ||
| ··Bracket | ||
| Injector Nozzle---------- | ||
| Oil Pump-- | ||
| Oil Pan--- | ||
| Exhaust Manifold--------- | ||
| Intake Manifold---------- |
Gain access
Enginedesk contains rich-data for parts and engines. The service is particulary useful for engine rebuilders and maintenance shops.
You can browse all information online. To get access to the technical data and parts information we provide the following options:
- Anytime 'all access' € 25,- * per month.
- Anytime 'all access' € 250,- * yearly.
* Excluding sales tax (21%)
Parts manufacturer
Reach thousands of remanufacturing companies. Promote your aftermarket parts and services world wide.
Please contact Enginedesk via info@enginedesk.com.
