Technical Data - OPEL S8U.770
Manufacturer OPEL
S8U.770 - I -
| Engine Type | S8U.770 |
| Fuel Supply System | I |
| Note |
| Cc | 2499 |
| Number of Cylinders | 4 |
| Bore Ø | 93.00 |
| Stroke | 92.00 |
| KW | 59 |
| Compression | 22.5 |
| KBA No. (Germany) | 4114371 |
| Type Mines | 905A3C |
| Technical Information Number | Technical Data | Information |
|---|---|---|
| Engine - Manufacturer---- | ||
| ····Construction Year (From - To) | ||
| ····Engine Output kW [HP] | ||
| ····Service Speed [1/min] | ||
| ····Number of Cylinders | ||
| ····Engine Code | ||
| ····Displacement (exact) [cc] | ||
| Compression-------------- | ||
| ····Compression - Ratio | ||
| Refs------ | ||
| ····Idle, min. | ||
| Exhaust Gas, value------- | ||
| ····Smoke Grey - Service RPM | ||
| ····Smoke Grey - Idle | ||
| Oil Pressure------------- | ||
| ····Oil Pressure, Operating Mode [atmosphere] | ||
| injection pump----------- | ||
| ··Type | ||
| ··Injection - Stage 1 => x | ||
| ····Injection (Point - ° before TDC) | ||
| ··Pressure, Fuel injection | ||
| =<>= | ||
| General Information - Cylinder Head ------------------------- | ||
| ··Cylinder Head - Height | ||
| ····New Part | ||
| ··warpage (value) - Cylinder Head | ||
| ····Standard Size | ||
| ····Measurement Range (Max.) - Machined | ||
| ··Thickness, Gasket | ||
| ··Thickness, Gasket | ||
| ··Thickness, Gasket | ||
| ··Thickness, Gasket | ||
| Valves---- | ||
| ··Valve Clearance [mm] | ||
| ····Operating Mode / Cold Check | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Head Diameter [D] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve stem diameter [d] - Inlet | ||
| ····Standard Size | ||
| ··Valve stem diameter [d] - Exhaust | ||
| ····Standard Size | ||
| ··Valve seat - Width S (Contact - Surface) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Seat Angle [°] | ||
| ····Inlet | ||
| ····Exhaust | ||
| Valve Spring------------- | ||
| ··Valve Spring - Length (Load/Empty) | ||
| ····Inner Diameter | ||
| ··Diameter - Spring, Material | ||
| ··Capacitive Load => Length 1 [mm] | ||
| ··Capacitive Load => Length 2 [mm] | ||
| ··Pressure Disc | ||
| Valve Lifter------------- | ||
| ··Outer Diameter - Standard Size | ||
| ··Outer Diameter - Standard Size | ||
| ····Clearance, Radial | ||
| Camshaft-- | ||
| ··Bore - Holder, Camshaft Bushes (Standard Size) | ||
| ··Diameter, Bearing Journal - Camshaft (Standard Size) | ||
| ··Clearance, Radial - Camshaft Bushes | ||
| ··Clearance, Axial - Camshaft Bushes | ||
| ··Valve lift | ||
| ····Inlet | ||
| ····Exhaust | ||
| =<>= | ||
| General Information - Engine Block | ||
| ··Bore - Holder, Cylinder Sleeve | ||
| ····Standard Size | ||
| ····1st Oversize | ||
| ··Press-fitted, Cylinder Sleeve | ||
| Cylinder Sleeve---------- | ||
| ··Outer Diameter - Cylinder Sleeve | ||
| ····Standard Size | ||
| ····1st Oversize | ||
| Piston---- | ||
| ··Diameter - Piston | ||
| ····Standard Size | ||
| ····Standard Size | ||
| ··Clearance - Piston | ||
| ··Clearance - Piston | ||
| Gudgeon Pin-------------- | ||
| ··Diameter - Gudgeon Pin | ||
| Piston Ring Set---------- | ||
| ··Piston Ring, Groove | ||
| ··1st Piston Ring, Lock - Clearance (Compression) | ||
| ··2nd Piston Ring, Lock - Clearance (Compression) | ||
| ··Piston Ring, Lock - Clearance (Oil Trap) | ||
| ··1st Piston Ring, Height - Clearance (Compression) | ||
| ··1st Piston Ring, Height - Clearance (Compression) | ||
| ··2nd Piston Ring, Height - Clearance (Compression) | ||
| ··2nd Piston Ring, Height - Clearance (Compression) | ||
| ··Piston Ring, Height - Clearance (Oil Trap) | ||
| ··Piston Ring, Height - Clearance (Oil Trap) | ||
| Connecting Rod----------- | ||
| ··Diameter, Bearing Journal - Connecting Rod | ||
| Crankshaft | ||
| ··Diameter, Bearing Journal - Crankshaft (Standard Size) | ||
| ··Bearing clearance - Axial Bearing | ||
| =<>= | ||
| Cylinder Head Bolts------ | ||
| ····Replace - Bolts | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| ····Stage 3 | ||
| Main Bearing Cap, crankshaft -------------------------------- | ||
| ····Replace - Bolts | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| Bearing Cap, connecting rod | ||
| ····Replace - Bolts | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| Crankshaft | ||
| Cranskhaft Pulley-------- | ||
| Flywheel-- | ||
| Camshaft, Bearing Cap---- | ||
| Drive gear - Camshaft---- | ||
| Glow Plug- | ||
| injection pump----------- | ||
| ··Support | ||
| ··Gear, injection pump | ||
| Injector Nozzle---------- | ||
| ····Injector Holder | ||
| Exhaust Manifold--------- | ||
| Intake Manifold---------- | ||
| Clutch Pressure Plate---- |
Gain access
Enginedesk contains rich-data for parts and engines. The service is particulary useful for engine rebuilders and maintenance shops.
You can browse all information online. To get access to the technical data and parts information we provide the following options:
- Anytime 'all access' € 25,- * per month.
- Anytime 'all access' € 250,- * yearly.
* Excluding sales tax (21%)
Parts manufacturer
Reach thousands of remanufacturing companies. Promote your aftermarket parts and services world wide.
Please contact Enginedesk via info@enginedesk.com.
