Technical Data - RENAULT F7P.700
Manufacturer RENAULT
F7P.700 - I - DOHC
| Engine Type | F7P.700 |
| Fuel Supply System | I |
| Note | DOHC |
| Cc | 1764 |
| Number of Cylinders | 4 |
| Bore Ø | 82.00 |
| Stroke | 83.50 |
| KW | 101 |
| Compression | 10 |
| KBA No. (Germany) | 4114371 |
| Type Mines | 905A3C |
| Technical Information Number | Technical Data | Information |
|---|---|---|
| ····Engine Code | ||
| Compression-------------- | ||
| ····Compression - Ratio | ||
| ····Compression - Pressure [bar] | ||
| Refs------ | ||
| ····Idle, min. | ||
| Exhaust Gas, value------- | ||
| ····CO Measurement, Idle | ||
| Oil Pressure------------- | ||
| ····Status (Operating Mode / Cold Check) | ||
| Thermostat | ||
| ····Thermostat, Opening Temperature | ||
| Ignition Timing---------- | ||
| ····Ignition System | ||
| Ignition - Row----------- | ||
| =<>= | ||
| General Information - Cylinder Head ------------------------- | ||
| ··Cylinder Head - Height | ||
| ····New Part | ||
| ··Height (Min.) - Machined | ||
| ··warpage (value) - Cylinder Head | ||
| ····Wear limitation | ||
| Valves---- | ||
| ··Valve Clearance [mm] | ||
| ··Valve Actuation, Setting | ||
| ····Inlet / Open (° before TDC) | ||
| ····Inlet / Closed (° after BDC) | ||
| ····Exhaust / Open (° before BDC) | ||
| ····Exhaust / Closed (° after TDC) | ||
| ··Valve Head Diameter [D] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve stem diameter [d] - Inlet | ||
| ····Standard Size | ||
| ··Valve stem diameter [d] - Exhaust | ||
| ····Standard Size | ||
| ··Valve Seat Angle [°] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Clearance - Valve Disc => Cylinder Head (Surface) | ||
| Valve Spring------------- | ||
| ··Min. Length [mm] => Capacitive Load 1 | ||
| ··Min. Length [mm] => Capacitive Load 2 | ||
| Valve Guides------------- | ||
| ··Fitting Angle | ||
| ··Fitted Height | ||
| ····Inlet | ||
| ····Inlet | ||
| ····Exhaust | ||
| ····Exhaust | ||
| ··Inner Diameter - Standard Size | ||
| ··Outer Diameter - Standard Size | ||
| ··Outer Diameter - 1st Oversize | ||
| Valve seat | ||
| ··Valve Seat Angle (B) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Seat - Measurement (A) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Seat - Outer Diameter, Standard Size | ||
| ····Inlet 1 | ||
| ····Exhaust | ||
| Valve Lifter------------- | ||
| ··Diameter - Valve Lifter | ||
| =<>= | ||
| General Information - Engine Block | ||
| Piston---- | ||
| ··Fitting Position | ||
| Connecting Rod----------- | ||
| ··Clearance, Axial - Big End Bearing | ||
| ··Diameter, Bearing Journal - Connecting Rod | ||
| ····Standard Size | ||
| ····1st Undersize | ||
| Crankshaft | ||
| ··Number of bearings | ||
| ··Diameter, Bearing Journal - Crankshaft (Standard Size) | ||
| ··Diameter, Bearing Journal - Crankshaft (1st Undersize) | ||
| ··Bearing clearance - Axial Bearing | ||
| Main Bearing scales, crankshaft ----------------------------- | ||
| ··Thickness, Axial Bearing (Bearing Shell) | ||
| ····Standard Size | ||
| ····1st Oversize | ||
| ····2nd Oversize | ||
| ····3rd Oversize | ||
| ····4th Oversize | ||
| Countershaft------------- | ||
| ··Bore - Holder, Countershaft | ||
| ····1st Bearing | ||
| ····2nd Bearing | ||
| ··Clearance, Axial - Balance Shaft | ||
| Cooling System----------- | ||
| ··Type | ||
| Timing Gear, Kit (Control)- | ||
| ··Clearance - Gear wheel (Tooth Pitch) | ||
| ··Clearance - Gear wheel (Tooth Pitch) | ||
| ··Clearance - Gear wheel (Tooth Pitch) | ||
| ··Clearance, Axial - Gear wheel | ||
| ··Clearance, Axial - Gear wheel | ||
| ··Clearance, Axial - Gear wheel | ||
| =<>= | ||
| Engine Timing Control | ||
| Tools | ||
| Cylinder Head------------ | ||
| ····Nut, Cylinder Head | ||
| Cylinder Head Bolts------ | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| ····Cooling Phase | ||
| ····Release | ||
| ····Stage 5 | ||
| ····Stage 6 | ||
| Main Bearing Cap, crankshaft -------------------------------- | ||
| Crankshaft | ||
| Crankshaft Gear---------- | ||
| Camshaft, Bearing Cap---- | ||
| Spark Plug | ||
| Oil Pump-- |
Gain access
Enginedesk contains rich-data for parts and engines. The service is particulary useful for engine rebuilders and maintenance shops.
You can browse all information online. To get access to the technical data and parts information we provide the following options:
- Anytime 'all access' € 25,- * per month.
- Anytime 'all access' € 250,- * yearly.
* Excluding sales tax (21%)
Parts manufacturer
Reach thousands of remanufacturing companies. Promote your aftermarket parts and services world wide.
Please contact Enginedesk via info@enginedesk.com.
