Engine Type | F8M.700 |
Fuel Supply System | I |
Note | SOHC/OHC |
Cc | 1595 |
Number of Cylinders | 4 |
Bore Ø | 78.00 |
Stroke | 83.50 |
KW | 40 |
Compression | 22.5 |
KBA No. (Germany) | 4114371 |
Type Mines | 905A3C |
Technical Information Number | Technical Data | Information |
---|---|---|
····Engine Code | ||
Compression-------------- | ||
····Compression - Ratio | ||
····Compression - Pressure [bar] | ||
····Cylinder - Differential pressure | ||
····Wear limitation | ||
Refs------ | ||
····Idle, min. | ||
····Idle, Max. | ||
····RPM, Max. | ||
Exhaust Gas, value------- | ||
····Smoke Grey - Service RPM | ||
Oil Pressure------------- | ||
····Status (Operating Mode / Cold Check) | ||
····Idle, min. | ||
····Rated Capacity | ||
····Position | ||
Thermostat | ||
····Thermostat, Opening Temperature | ||
Ignition Timing---------- | ||
····Ignition System | ||
Ignition - Row----------- | ||
····Ignition Point, Static / Dynamic | ||
····Ignition Point, Static / Dynamic | ||
injection pump----------- | ||
··Injection - Stage 1 => x | ||
··Pressure, Fuel injection | ||
··Pressure, Fuel injection | ||
··Pressure, Fuel injection | ||
=<>= | ||
General Information - Cylinder Head ------------------------- | ||
··Cylinder Head - Height | ||
····New Part | ||
··warpage (value) - Cylinder Head | ||
····Standard Size | ||
····Wear limitation | ||
····Notes | ||
··Thickness, Gasket | ||
··Thickness, Gasket | ||
··Thickness, Gasket | ||
··Thickness, Gasket | ||
··Cylinder Head Gasket, Markings | ||
··Cylinder Head Gasket, Markings | ||
··Cylinder Head Gasket, Markings | ||
··Cylinder Head Gasket, Markings | ||
Pre-chamber-------------- | ||
··Protrusion -/+, Pre-combustion chamber | ||
··Bore - Holder, Pre-chamber | ||
····Standard Size | ||
····Standard Size | ||
Valves---- | ||
··Valve Clearance [mm] | ||
····Operating Mode / Cold Check | ||
····Inlet | ||
····Exhaust | ||
··Valve Clearance - Cold Check [mm] | ||
··Valve Actuation, Setting | ||
····Inlet / Open (° before TDC) | ||
····Inlet / Closed (° after BDC) | ||
····Exhaust / Open (° before BDC) | ||
····Exhaust / Closed (° after TDC) | ||
··Valve Head Diameter [D] | ||
····Inlet | ||
····Inlet | ||
····Exhaust | ||
··Valve stem diameter [d] - Inlet | ||
··Valve stem diameter [d] - Exhaust | ||
··Valve Seat Angle [°] | ||
····Inlet | ||
····Exhaust | ||
··Valve - Protrusion (+/-) | ||
····Inlet | ||
····Exhaust | ||
Valve Spring------------- | ||
··Valve Spring - Length (Load/Empty) | ||
··Min. Length [mm] => Capacitive Load 1 | ||
··Min. Length [mm] => Capacitive Load 2 | ||
Valve Guides------------- | ||
··Fitted Height | ||
····Inlet | ||
····Exhaust | ||
··Inner Diameter - Standard Size | ||
····Inlet | ||
····Exhaust | ||
··Outer Diameter - Standard Size | ||
····Inlet | ||
····Exhaust | ||
··Outer Diameter - 1st Oversize | ||
····Inlet | ||
····Exhaust | ||
··Bore - Holder, Valve Guides (Standard Size) | ||
····Inlet | ||
····Exhaust | ||
Valve seat | ||
··Valve Seat Angle (B) | ||
····Inlet | ||
····Exhaust | ||
··Valve Seat - Measurement (A) | ||
··Valve Seat - Diameter (D) | ||
····Inlet | ||
····Inlet | ||
····Exhaust | ||
····Exhaust | ||
Valve Lifter------------- | ||
··Diameter - Valve Lifter | ||
Camshaft-- | ||
··Clearance, Axial - Camshaft Bushes | ||
=<>= | ||
General Information - Engine Block | ||
Cylinder Sleeve---------- | ||
··Bore | ||
··Bore | ||
····Standard Size | ||
····Standard Size | ||
····Standard Size | ||
····Standard Size | ||
····Standard Size | ||
····Standard Size | ||
····Standard Size | ||
····Standard Size | ||
Piston---- | ||
··Diameter - Piston | ||
····Standard Size | ||
····Standard Size | ||
····Standard Size | ||
····Standard Size | ||
····Standard Size | ||
····Standard Size | ||
····Standard Size | ||
····Standard Size | ||
····Standard Size | ||
····Standard Size | ||
····Standard Size | ||
····Standard Size | ||
····Standard Size | ||
····Standard Size | ||
····Standard Size | ||
····Standard Size | ||
····Measurement (Position) | ||
Piston Ring Set---------- | ||
··Height, 1st Piston Ring (Compression) | ||
··Height, 2nd Piston Ring (Compression) | ||
··Height, Piston Ring (Oil Trap) | ||
Connecting Rod----------- | ||
··Inner Diameter - Big End Bearing | ||
··Clearance, Axial - Big End Bearing | ||
··Diameter, Bearing Journal - Connecting Rod | ||
····Standard Size | ||
····1st Undersize | ||
Crankshaft | ||
··Number of bearings | ||
··Diameter, Bearing Journal - Crankshaft (Standard Size) | ||
··Diameter, Bearing Journal - Crankshaft (1st Undersize) | ||
··Bearing clearance - Axial Bearing | ||
Main Bearing scales, crankshaft ----------------------------- | ||
··Thickness, Axial Bearing (Bearing Shell) | ||
··Thickness, Axial Bearing (Bearing Shell) | ||
··Thickness, Axial Bearing (Bearing Shell) | ||
··Thickness, Axial Bearing (Bearing Shell) | ||
··Thickness, Axial Bearing (Bearing Shell) | ||
Cooling System----------- | ||
··Type | ||
··Clearance - Drive gear => Housing, Pump | ||
Timing Gear, Kit (Control)- | ||
··Clearance, Axial - Gear wheel | ||
=<>= | ||
Engine Timing Control | ||
Engine Timing Control | ||
Tools | ||
Cylinder Head Bolts------ | ||
····Stage 1 | ||
····Stage 2 | ||
····Release | ||
····Cooling Phase | ||
····Stage 3 | ||
····Stage 4 | ||
····Bolt Length - Max. | ||
Main Bearing Cap, crankshaft -------------------------------- | ||
····Bolt Length - Max. | ||
····Bolt Length - Max. | ||
Bearing Cap, connecting rod | ||
Crankshaft | ||
Crankshaft Gear---------- | ||
Flywheel-- | ||
Camshaft, Bearing Cap---- | ||
Drive gear - Camshaft---- | ||
Glow Plug- | ||
Injector Nozzle---------- | ||
Oil Pump-- | ||
Oil Pan--- |
Enginedesk contains rich-data for parts and engines. The service is particulary useful for engine rebuilders and maintenance shops.
You can browse all information online. To get access to the technical data and parts information we provide the following options:
* Excluding sales tax (21%)
Reach thousands of remanufacturing companies. Promote your aftermarket parts and services world wide.
Please contact Enginedesk via info@enginedesk.com.