Technical Data - RENAULT G8T.708
Manufacturer RENAULT
G8T.708 - T - Turbo Diesel
| Engine Type | G8T.708 |
| Fuel Supply System | T |
| Note | Turbo Diesel |
| Cc | 2188 |
| Number of Cylinders | 4 |
| Bore Ø | 87.00 |
| Stroke | 92.00 |
| KW | 83 |
| Compression | 22 |
| KBA No. (Germany) | 4114371 |
| Type Mines | 905A3C |
| Technical Information Number | Technical Data | Information |
|---|---|---|
| ····Engine Code | ||
| Compression-------------- | ||
| ····Compression - Ratio | ||
| Refs------ | ||
| ····Idle, min. | ||
| Exhaust Gas, value------- | ||
| Oil Pressure------------- | ||
| ····Idle, min. | ||
| ····Rated Capacity | ||
| Thermostat | ||
| ····Thermostat, Opening Temperature | ||
| injection pump----------- | ||
| ··Injection - Stage 1 => x | ||
| ··Pressure, Fuel injection | ||
| ····New Part | ||
| ····Min. | ||
| =<>= | ||
| General Information - Cylinder Head ------------------------- | ||
| ··Cylinder Head - Height | ||
| ··warpage (value) - Cylinder Head | ||
| ····Wear limitation | ||
| ····Notes | ||
| Pre-chamber-------------- | ||
| ··Protrusion -/+, Pre-combustion chamber | ||
| ··Outer Diameter - Pre-chamber | ||
| ····Standard Size | ||
| ··Bore - Holder, Pre-chamber | ||
| ····Standard Size | ||
| Valves---- | ||
| ··Valve Actuation, Setting | ||
| ····Inlet / Open (° before TDC) | ||
| ····Inlet / Closed (° after BDC) | ||
| ····Exhaust / Open (° before BDC) | ||
| ····Exhaust / Closed (° after TDC) | ||
| ··Valve Head Diameter [D] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve stem diameter [d] - Inlet | ||
| ··Valve stem diameter [d] - Exhaust | ||
| ··Valve Seat Angle [°] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve - Protrusion (+/-) | ||
| Valve Spring------------- | ||
| ··Valve Spring - Length (Load/Empty) | ||
| ··Min. Length [mm] => Capacitive Load 1 | ||
| ··Min. Length [mm] => Capacitive Load 2 | ||
| Valve Guides------------- | ||
| ··Fitted Height | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Inner Diameter - Standard Size | ||
| ··Outer Diameter - Standard Size | ||
| Valve seat | ||
| ··Valve Seat Angle (B) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Seat - Measurement (A) | ||
| ····Inlet | ||
| ····Wear limitation - Inlet | ||
| ····Exhaust | ||
| ····Wear limitation - Outlet | ||
| ··Valve Seat - Outer Diameter, Standard Size | ||
| ····Inlet 1 | ||
| ····Exhaust | ||
| Camshaft-- | ||
| ··Clearance, Axial - Camshaft Bushes | ||
| ····Wear limitation | ||
| =<>= | ||
| Cylinder Sleeve---------- | ||
| ··Bore | ||
| ····Standard Size | ||
| ····Standard Size | ||
| Piston---- | ||
| ··Fitting Position | ||
| Piston Ring Set---------- | ||
| ··Height, 1st Piston Ring (Compression) | ||
| ··Height, 2nd Piston Ring (Compression) | ||
| ··Height, Piston Ring (Oil Trap) | ||
| Connecting Rod----------- | ||
| ··Distance, Centre - Small End Bush / Big End Bearing | ||
| ··Distance, Centre - Small End Bush / Big End Bearing | ||
| ··Distance, Centre - Small End Bush / Big End Bearing | ||
| ··Distance, Centre - Small End Bush / Big End Bearing | ||
| ··Diameter, Bearing Journal - Connecting Rod | ||
| ····Standard Size | ||
| Crankshaft | ||
| ··Number of bearings | ||
| ··Centering - Crankshaft (Tolerance) | ||
| ··Grindable | ||
| ··Diameter, Bearing Journal - Crankshaft (Standard Size) | ||
| ··Bearing clearance - Axial Bearing | ||
| =<>= | ||
| Engine Timing Control | ||
| Tools | ||
| Mounting Type - Flywheel | ||
| Cylinder Head Bolts------ | ||
| ····Replace - Bolts | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| ····Stage 2 | ||
| ····Stage 2 | ||
| ····Stage 2 | ||
| ····Stage 3 | ||
| ····Release | ||
| ····Stage 4 | ||
| ····Stage 4 | ||
| ····Release | ||
| ····Stage 5 | ||
| ····Stage 5 | ||
| ····Stage 5 | ||
| ····Stage 5 | ||
| ····Release | ||
| ····Stage 6 | ||
| ····Stage 6 | ||
| ····Stage 6 | ||
| ····Stage 6 | ||
| ····Release | ||
| ····Stage 7 | ||
| ····Stage 7 | ||
| ····Stage 7 | ||
| ····Stage 7 | ||
| ····Release | ||
| ····Stage 8 | ||
| ····Stage 8 | ||
| ····Stage 8 | ||
| ····Stage 8 | ||
| Main Bearing Cap, crankshaft -------------------------------- | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| Bearing Cap, connecting rod | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| Crankshaft | ||
| Crankshaft Gear---------- | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| Flywheel-- | ||
| Camshaft, Bearing Cap---- | ||
| Drive gear - Camshaft---- | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| Glow Plug- | ||
| Injector Nozzle---------- | ||
| Oil Pump-- | ||
| Oil Pan--- | ||
| Intake Manifold---------- |
Gain access
Enginedesk contains rich-data for parts and engines. The service is particulary useful for engine rebuilders and maintenance shops.
You can browse all information online. To get access to the technical data and parts information we provide the following options:
- Anytime 'all access' € 25,- * per month.
- Anytime 'all access' € 250,- * yearly.
* Excluding sales tax (21%)
Parts manufacturer
Reach thousands of remanufacturing companies. Promote your aftermarket parts and services world wide.
Please contact Enginedesk via info@enginedesk.com.
