Technical Data - RENAULT J7R.752
Manufacturer RENAULT
J7R.752 - T - SOHC/OHC
| Engine Type | J7R.752 |
| Fuel Supply System | T |
| Note | SOHC/OHC |
| Cc | 1995 |
| Number of Cylinders | 4 |
| Bore Ø | 88.00 |
| Stroke | 82.00 |
| KW | 129 |
| Compression | 8.00 |
| KBA No. (Germany) | 4114371 |
| Type Mines | 905A3C |
| Technical Information Number | Technical Data | Information |
|---|---|---|
| ····Engine Code | ||
| Charger--- | ||
| ··Type | ||
| ····Manufacturer + Version | ||
| ····Intercooler, charger | ||
| ····Turbocharger - Pressure (Max.) | ||
| Compression-------------- | ||
| ····Compression - Ratio | ||
| ····Compression - Pressure [bar] | ||
| Refs------ | ||
| ····Idle, min. | ||
| Exhaust Gas, value------- | ||
| ····CO Measurement, Idle | ||
| ····CO2 Measurement, Idle [%] | ||
| ····HC Measurement, Idle | ||
| Oil Pressure------------- | ||
| ····Status (Operating Mode / Cold Check) | ||
| ····Idle, min. | ||
| ····Rated Capacity | ||
| Thermostat | ||
| ····Thermostat, Opening Temperature | ||
| Ignition Timing---------- | ||
| ····Ignition System | ||
| Ignition - Row----------- | ||
| =<>= | ||
| General Information - Cylinder Head ------------------------- | ||
| ··Cylinder Head - Number | ||
| ··Unleaded - Design | ||
| ··Cylinder Head - Height | ||
| ··warpage (value) - Cylinder Head | ||
| ····Standard Size | ||
| ····Notes | ||
| Valves---- | ||
| ··Valve Clearance [mm] | ||
| ····Operating Mode / Cold Check | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Head Diameter [D] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve stem diameter [d] - Inlet | ||
| ··Valve stem diameter [d] - Exhaust | ||
| ··Valve Seat Angle [°] | ||
| ····Inlet | ||
| ····Exhaust | ||
| Valve Spring------------- | ||
| Valve Guides------------- | ||
| ··Material | ||
| ··Fitted Height | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Guide - Length [mm] | ||
| ··Inner Diameter - Standard Size | ||
| ··Outer Diameter - Standard Size | ||
| ··Outer Diameter - 1st Oversize | ||
| ··Outer Diameter - 2nd Oversize | ||
| ··Outer Diameter - 3rd Oversize | ||
| ··Bore - Holder, Valve Guides (Standard Size) | ||
| ··Bore - Holder, Valve Guides (1st Oversize) | ||
| ··Bore - Holder, Valve Guides (2nd Oversize) | ||
| ··Bore - Holder, Valve Guides (3rd Oversize) | ||
| ··Press-fitted, Valve Guides | ||
| Valve seat | ||
| ··Valve Seat - Height, Standard Size (H) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Seat - Height, 1st Oversize (H) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Seat Angle (B) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Seat - Measurement (A) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Seat - Outer Diameter, Standard Size | ||
| ····Inlet 1 | ||
| ····Exhaust | ||
| ··Valve Seat - Outer Diameter, 1st Oversize | ||
| ····Inlet | ||
| ····Exhaust | ||
| Camshaft-- | ||
| ··Clearance, Axial - Camshaft Bushes | ||
| =<>= | ||
| General Information - Engine Block | ||
| ··Material | ||
| ··Bore - Holder, Main Bearings (Engine Block) | ||
| ··Bore - Holder, Cylinder Sleeve | ||
| ··Cylinder Sleeve Protrusion | ||
| ····Height - Cylinder Sleeve (different) | ||
| Cylinder Sleeve---------- | ||
| Cylinder Sleeve---------- | ||
| Piston---- | ||
| ··Fitting Position | ||
| ····Possible - Compression Height | ||
| Gudgeon Pin-------------- | ||
| ····Press-fitted (Temperature -C°) | ||
| Piston Ring Set---------- | ||
| ··Height, 1st Piston Ring (Compression) | ||
| ··Height, 2nd Piston Ring (Compression) | ||
| ··Height, Piston Ring (Oil Trap) | ||
| Connecting Rod----------- | ||
| ··Fitting Position | ||
| ··Fitting Position | ||
| ··Bore - Holder, Connecting Rod (Big End Bearing) | ||
| ··Clearance, Radial - Big End Bearing | ||
| ··Clearance, Axial - Big End Bearing | ||
| ··Diameter, Bearing Journal - Connecting Rod | ||
| ····Standard Size | ||
| ····1st Undersize | ||
| ··Thickness, Big End Bearings | ||
| ····Fitting Position | ||
| ····Fitting Position | ||
| Crankshaft | ||
| ··Number of bearings | ||
| ··Centering - Crankshaft (Tolerance) | ||
| ··Grindable | ||
| ··Diameter, Bearing Journal - Crankshaft (Standard Size) | ||
| ··Diameter, Bearing Journal - Crankshaft (1st Undersize) | ||
| ··Clearance - Main Bearing, crankshaft | ||
| ··Bearing clearance - Axial Bearing | ||
| Main Bearing scales, crankshaft ----------------------------- | ||
| ··Thickness, Axial Bearing (Bearing Shell) | ||
| Cooling System----------- | ||
| ··Type | ||
| ··Clearance - Outer, Rotor => Housing, Oil Pump | ||
| ··Clearance, Axial - Gear wheels => Oil Pump Housing Lid | ||
| =<>= | ||
| Engine Timing Control | ||
| Engine Timing Control | ||
| Tools | ||
| Valve Cover-------------- | ||
| Cylinder Head Bolts------ | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| ····Stage 3 | ||
| ····Stage 4 | ||
| ····Stage 5 | ||
| ····Stage 6 | ||
| Main Bearing Cap, crankshaft -------------------------------- | ||
| Bearing Cap, connecting rod | ||
| Crankshaft | ||
| Crankshaft Gear---------- | ||
| Crankshaft Gear---------- | ||
| Flywheel-- | ||
| Flywheel-- | ||
| Driver Plate------------- | ||
| Driver Plate------------- | ||
| Drive gear - Camshaft---- | ||
| Timing Case-------------- | ||
| ··Timing Chain Tensioner | ||
| ····Chain Tensioner | ||
| Oil Pump-- | ||
| Oil Pan--- | ||
| ····Notes |
Gain access
Enginedesk contains rich-data for parts and engines. The service is particulary useful for engine rebuilders and maintenance shops.
You can browse all information online. To get access to the technical data and parts information we provide the following options:
- Anytime 'all access' € 25,- * per month.
- Anytime 'all access' € 250,- * yearly.
* Excluding sales tax (21%)
Parts manufacturer
Reach thousands of remanufacturing companies. Promote your aftermarket parts and services world wide.
Please contact Enginedesk via info@enginedesk.com.
