Technical Data - RENAULT J8S.746
Manufacturer RENAULT
J8S.746 - T - SOHC/OHC
| Engine Type | J8S.746 |
| Fuel Supply System | T |
| Note | SOHC/OHC |
| Cc | 2068 |
| Number of Cylinders | 4 |
| Bore Ø | 86.00 |
| Stroke | 89.00 |
| KW | 65 |
| Compression | 21.5 |
| KBA No. (Germany) | 4114371 |
| Type Mines | 905A3C |
| Technical Information Number | Technical Data | Information |
|---|---|---|
| ····Engine Code | ||
| Charger--- | ||
| ··Type | ||
| ····Manufacturer + Version | ||
| ····Intercooler, charger | ||
| ····Turbocharger - Pressure (Max.) | ||
| Compression-------------- | ||
| ····Compression - Ratio | ||
| ····Compression - Pressure [bar] | ||
| Refs------ | ||
| ····Idle, min. | ||
| ····Idle, Max. | ||
| ····RPM, Max. | ||
| Exhaust Gas, value------- | ||
| ····Smoke Grey - Service RPM | ||
| Oil Pressure------------- | ||
| ····Status (Operating Mode / Cold Check) | ||
| ····Idle, min. | ||
| ····Rated Capacity | ||
| Thermostat | ||
| ····Thermostat, Opening Temperature | ||
| Ignition Timing---------- | ||
| ····Ignition System | ||
| Ignition - Row----------- | ||
| =<>= | ||
| General Information - Cylinder Head ------------------------- | ||
| ··Cylinder Head - Number | ||
| ··Cylinder Head - Height | ||
| ··warpage (value) - Cylinder Head | ||
| ····Standard Size | ||
| ····Notes | ||
| ··Thickness, Gasket | ||
| ····1st Oversize | ||
| ····2nd Oversize | ||
| ····3rd Oversize | ||
| ··Cylinder Head Gasket, Markings | ||
| ····1st Oversize | ||
| ····2nd Oversize | ||
| ····3rd Oversize | ||
| ··Piston Crown Clearance -/+ | ||
| ····1st Oversize | ||
| ····2nd Oversize | ||
| ····3rd Oversize | ||
| Pre-chamber-------------- | ||
| ··Protrusion -/+, Pre-combustion chamber | ||
| ··Outer Diameter - Pre-chamber | ||
| ··Bore - Holder, Pre-chamber | ||
| Valves---- | ||
| ··Valve Clearance [mm] | ||
| ····Operating Mode / Cold Check | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Clearance - Cold Check [mm] | ||
| ··Valve Actuation, Setting | ||
| ····Inlet / Open (° before TDC) | ||
| ····Inlet / Closed (° after BDC) | ||
| ····Exhaust / Open (° before BDC) | ||
| ····Exhaust / Closed (° after TDC) | ||
| ··Valve Head Diameter [D] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve stem diameter [d] - Inlet | ||
| ··Valve stem diameter [d] - Exhaust | ||
| ··Valve Seat Angle [°] | ||
| ··Clearance - Valve Disc => Cylinder Head (Surface) | ||
| Valve Spring------------- | ||
| ··Valve Spring - Length (Load/Empty) | ||
| ··Min. Length [mm] => Capacitive Load 1 | ||
| ··Min. Length [mm] => Capacitive Load 2 | ||
| Valve Guides------------- | ||
| ··Material | ||
| ··Fitted Height | ||
| ··Valve Guide - Length [mm] | ||
| ··Inner Diameter - Standard Size | ||
| ··Outer Diameter - Standard Size | ||
| ··Outer Diameter - 1st Oversize | ||
| ··Bore - Holder, Valve Guides (Standard Size) | ||
| ··Bore - Holder, Valve Guides (1st Oversize) | ||
| ··Clearance - Valve => Valve Guides | ||
| Valve seat | ||
| ··Valve Seat Angle (B) | ||
| ··Adaptation - Angle (B2) | ||
| ··Valve Seat - Measurement (A) | ||
| ··Valve Seat - Outer Diameter, Standard Size | ||
| ····Inlet 1 | ||
| ····Exhaust | ||
| Camshaft-- | ||
| ··Clearance, Axial - Camshaft Bushes | ||
| General Information - Engine Block | ||
| ··Bore - Holder, Main Bearings (Engine Block) | ||
| ··Bore - Holder, Cylinder Sleeve | ||
| ··Cylinder Sleeve Protrusion | ||
| ····Height - Cylinder Sleeve (different) | ||
| Cylinder Sleeve---------- | ||
| Cylinder Sleeve---------- | ||
| ··Inner Diameter - Cylinder Sleeve | ||
| ··Outer Diameter - Cylinder Sleeve | ||
| Piston---- | ||
| ··Fitting Position | ||
| ····Possible - Compression Height | ||
| Gudgeon Pin-------------- | ||
| ····Press-fitted (Temperature -C°) | ||
| Piston Ring Set---------- | ||
| ··Height, 1st Piston Ring (Compression) | ||
| ··Height, 2nd Piston Ring (Compression) | ||
| ··Height, Piston Ring (Oil Trap) | ||
| Connecting Rod----------- | ||
| ··Fitting Position | ||
| ··Bore - Holder, Connecting Rod (Small End Bushes) | ||
| ··Bore - Holder, Connecting Rod (Big End Bearing) | ||
| ··Clearance, Radial - Big End Bearing | ||
| ··Clearance, Axial - Big End Bearing | ||
| ··Diameter, Bearing Journal - Connecting Rod | ||
| ····Standard Size | ||
| ····1st Undersize | ||
| ··Thickness, Big End Bearings | ||
| ····Fitting Position | ||
| Crankshaft | ||
| ··Number of bearings | ||
| ··Centering - Crankshaft (Tolerance) | ||
| ··Grindable | ||
| ··Diameter, Bearing Journal - Crankshaft (Standard Size) | ||
| ··Diameter, Bearing Journal - Crankshaft (1st Undersize) | ||
| ··Clearance - Main Bearing, crankshaft | ||
| ··Bearing clearance - Axial Bearing | ||
| Main Bearing scales, crankshaft ----------------------------- | ||
| ··Fitting Position | ||
| ··Thickness, Axial Bearing (Bearing Shell) | ||
| ····Fitting Position | ||
| ····Standard Size | ||
| ····1st Oversize | ||
| ····2nd Oversize | ||
| ····3rd Oversize | ||
| Cooling System----------- | ||
| ··Type | ||
| ··Clearance - Outer, Rotor => Housing, Oil Pump | ||
| ··Clearance, Axial - Gear wheels => Oil Pump Housing Lid | ||
| =<>= | ||
| Engine Timing Control | ||
| Tools | ||
| Cylinder Head Bolts------ | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| ····Stage 3 | ||
| ····Stage 4 | ||
| ····Stage 5 | ||
| ····Stage 6 | ||
| ····Release | ||
| ····Retouching | ||
| Main Bearing Cap, crankshaft -------------------------------- | ||
| Bearing Cap, connecting rod | ||
| Crankshaft | ||
| Crankshaft Gear---------- | ||
| Flywheel-- | ||
| Driver Plate------------- | ||
| Rocker Arm Shaft, valve train ------------------------------- | ||
| ··Rocker Arm Bridge | ||
| Drive gear - Camshaft---- | ||
| Glow Plug- | ||
| Injector Nozzle---------- | ||
| ····Injector Holder | ||
| ····Injector Holder | ||
| Oil Pump-- | ||
| Oil Pan--- |
Gain access
Enginedesk contains rich-data for parts and engines. The service is particulary useful for engine rebuilders and maintenance shops.
You can browse all information online. To get access to the technical data and parts information we provide the following options:
- Anytime 'all access' € 25,- * per month.
- Anytime 'all access' € 250,- * yearly.
* Excluding sales tax (21%)
Parts manufacturer
Reach thousands of remanufacturing companies. Promote your aftermarket parts and services world wide.
Please contact Enginedesk via info@enginedesk.com.
