Technical Data - ROVER 20 T2R (L SERIES)
Manufacturer ROVER
20 T2R (L SERIES) - T - SOHC/OHC
| Engine Type | 20 T2R (L SERIES) |
| Fuel Supply System | T |
| Note | SOHC/OHC |
| Cc | 1994 |
| Number of Cylinders | 4 |
| Bore Ø | 84.50 |
| Stroke | 88.90 |
| KW | 64 |
| Compression | 19.5 |
| KBA No. (Germany) | 4114371 |
| Type Mines | 905A3C |
| Technical Information Number | Technical Data | Information |
|---|---|---|
| ····Engine Code | ||
| Compression-------------- | ||
| ····Compression - Ratio | ||
| Refs------ | ||
| ····Idle, min. | ||
| Exhaust Gas, value------- | ||
| Oil Pressure------------- | ||
| ····Status (Operating Mode / Cold Check) | ||
| ····Idle, min. | ||
| ····Rated Capacity | ||
| Thermostat | ||
| ····Thermostat, Opening Temperature | ||
| Ignition Timing---------- | ||
| ····Ignition System | ||
| Ignition - Row----------- | ||
| injection pump----------- | ||
| ··Pressure, Fuel injection | ||
| ····New Part | ||
| =<>= | ||
| General Information - Cylinder Head ------------------------- | ||
| ··warpage (value) - Cylinder Head | ||
| ····Wear limitation | ||
| ····Measurement Range (Max.) - Machined | ||
| ··Cylinder Head Gasket, Markings | ||
| ··Cylinder Head Gasket, Markings | ||
| ··Cylinder Head Gasket, Markings | ||
| ··Cylinder Head Gasket, Markings | ||
| Valves---- | ||
| ··Valve Clearance [mm] | ||
| ··Valve stem diameter [d] - Inlet | ||
| ····Standard Size | ||
| ··Valve stem diameter [d] - Exhaust | ||
| ····Standard Size | ||
| ··Valve Seat Angle [°] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve - Protrusion (+/-) | ||
| ····Inlet | ||
| ····Wear limitation - Inlet | ||
| ··Valves, Fitted Height | ||
| ····Inlet | ||
| ····Exhaust | ||
| Valve Spring------------- | ||
| ··Valve Spring - Length (Load/Empty) | ||
| Valve Guides------------- | ||
| ··Temperature Range [°C] - Press-out | ||
| ··Fitted Height | ||
| ··Bore - Holder, Valve Guides (Standard Size) | ||
| ··Clearance - Valve => Valve Guides | ||
| ····Inlet | ||
| ····Exhaust | ||
| Valve seat | ||
| ··Valve Seat Angle (B) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Seat - Measurement (A) | ||
| ····Inlet | ||
| ····Exhaust | ||
| Valve Lifter------------- | ||
| ··Diameter - Valve Lifter | ||
| ····Standard Size | ||
| Camshaft-- | ||
| ··Clearance, Radial - Camshaft Bushes | ||
| ··Clearance, Axial - Camshaft Bushes | ||
| ····Wear limitation | ||
| =<>= | ||
| General Information - Engine Block | ||
| Cylinder Sleeve---------- | ||
| ··Bore | ||
| ··Bore | ||
| Piston---- | ||
| ··Diameter - Piston | ||
| ····Standard Size | ||
| ····Measurement (Position) | ||
| Piston Ring Set---------- | ||
| ··Piston Ring, Groove | ||
| ··1st Piston Ring, Lock - Clearance (Compression) | ||
| ··2nd Piston Ring, Lock - Clearance (Compression) | ||
| ··Piston Ring, Lock - Clearance (Oil Trap) | ||
| ··1st Piston Ring, Height - Clearance (Compression) | ||
| ··2nd Piston Ring, Height - Clearance (Compression) | ||
| ··Piston Ring, Height - Clearance (Oil Trap) | ||
| Connecting Rod----------- | ||
| ··Clearance, Radial - Big End Bearing | ||
| ··Diameter, Bearing Journal - Connecting Rod | ||
| Crankshaft | ||
| ··Diameter, Bearing Journal - Crankshaft (Standard Size) | ||
| ··Clearance - Main Bearing, crankshaft | ||
| ··Bearing clearance - Axial Bearing | ||
| ····Wear limitation | ||
| Main Bearing scales, crankshaft ----------------------------- | ||
| ··Thickness, Axial Bearing (Bearing Shell) | ||
| ····Standard Size | ||
| Cooling System----------- | ||
| ··Clearance, Axial - Outer, Rotor (Housing, Oil Pump) | ||
| ··Clearance - Outer, Rotor => Inside, Rotor | ||
| ··Clearance - Outer, Rotor => Housing, Oil Pump | ||
| =<>= | ||
| Engine Timing Control | ||
| Belt Drive (Fuel Pump) | ||
| Tools | ||
| Tools (Crankshaft) | ||
| Valve Cover-------------- | ||
| Cylinder Head Bolts------ | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| ····Stage 3 | ||
| ····Stage 4 | ||
| ····Bolt Length - Max. | ||
| Main Bearing Cap, crankshaft -------------------------------- | ||
| Bearing Cap, connecting rod | ||
| ····Replace - Bolts | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| ····Nut | ||
| Crankshaft | ||
| Crankshaft Gear---------- | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| Flywheel-- | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| Camshaft, Bearing Cap---- | ||
| Drive gear - Camshaft---- | ||
| Drive gear - Camshaft---- | ||
| Timing Case-------------- | ||
| ··Timing Belt Tensioner | ||
| Oil Pump-- | ||
| Oil Pan--- | ||
| ··Oil Drain Plug, oil pan | ||
| Exhaust Manifold--------- | ||
| ····Bolt | ||
| ··adjusting nut | ||
| Intake Manifold---------- | ||
| ····Bolt | ||
| ··adjusting nut |
Gain access
Enginedesk contains rich-data for parts and engines. The service is particulary useful for engine rebuilders and maintenance shops.
You can browse all information online. To get access to the technical data and parts information we provide the following options:
- Anytime 'all access' € 25,- * per month.
- Anytime 'all access' € 250,- * yearly.
* Excluding sales tax (21%)
Parts manufacturer
Reach thousands of remanufacturing companies. Promote your aftermarket parts and services world wide.
Please contact Enginedesk via info@enginedesk.com.
