Technical Data - SCANIA DS 9.01(L01-L02)
Manufacturer SCANIA
DS 9.01(L01-L02) - T - Turbo
| Engine Type | DS 9.01(L01-L02) |
| Fuel Supply System | T |
| Note | Turbo |
| Cc | 8480 |
| Number of Cylinders | 6 |
| Bore Ø | 115.00 |
| Stroke | 136.39 |
| KW | 180 |
| Compression | 15.5 |
| KBA No. (Germany) | 4114371 |
| Type Mines | 905A3C |
| Technical Information Number | Technical Data | Information |
|---|---|---|
| =<>= | ||
| Valves---- | ||
| ··Valve Clearance - Cold Check [mm] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Actuation, Setting | ||
| ····Inlet / Open (° before TDC) | ||
| ····Inlet / Closed (° after BDC) | ||
| ····Exhaust / Open (° before BDC) | ||
| ····Exhaust / Closed (° after TDC) | ||
| ··Valve Head Diameter [D] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valves - Length (L) | ||
| ····Inlet - New Part | ||
| ····Exhaust - New Part | ||
| ··Valve lift | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve stem diameter [d] - Inlet | ||
| ····Material | ||
| ····Standard Size | ||
| ··Valve stem diameter [d] - Exhaust | ||
| ····Material | ||
| ····Standard Size | ||
| ··Valve Seat Angle [°] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Disc, Thickness (t) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Clearance - Valve Disc => Cylinder Head (Surface) | ||
| ····Inlet | ||
| ····Wear limitation - Inlet | ||
| ····Exhaust | ||
| ····Wear limitation - Outlet | ||
| Valve Spring------------- | ||
| ··Valve Spring - Length (Load/Empty) | ||
| ····Inlet - inner | ||
| ····Exhaust - inner | ||
| ····Inlet - Outer | ||
| ····Exhaust - Outer | ||
| Valve Guides------------- | ||
| ··Material | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Fitted Height | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Guide - Length [mm] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Inner Diameter - Standard Size | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Outer Diameter - Standard Size | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Clearance - Valve => Valve Guides | ||
| ····Inlet | ||
| ····Exhaust | ||
| Valve seat | ||
| ··Valve Seat Angle (B) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Adaptation - Angle (B2) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Seat - Measurement (A) | ||
| ····Inlet | ||
| ····Exhaust | ||
| Camshaft-- | ||
| ··Clearance, Axial - Camshaft Bushes | ||
| =<>= | ||
| General Information - Engine Block | ||
| ··Engine Block - Height | ||
| ····Machined - permitted | ||
| ··Cylinder Sleeve Protrusion | ||
| Piston Ring Set---------- | ||
| ··Piston Ring, Groove | ||
| ··1st Piston Ring, Lock - Clearance (Compression) | ||
| ··2nd Piston Ring, Lock - Clearance (Compression) | ||
| ··Piston Ring, Lock - Clearance (Oil Trap) | ||
| Connecting Rod----------- | ||
| ··Bore - Holder, Connecting Rod (Big End Bearing) | ||
| ··Clearance, Radial - Big End Bearing | ||
| ··Clearance, Axial - Big End Bearing | ||
| ··Diameter, Bearing Journal - Connecting Rod | ||
| ····Standard Size | ||
| Crankshaft | ||
| ··Diameter, Bearing Journal - Crankshaft (Standard Size) | ||
| ··Housing Diameter - Main Bearings | ||
| ··Clearance - Main Bearing, crankshaft | ||
| =<>= | ||
| Cylinder Head Bolts------ | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| ····Stage 3 | ||
| ····Stage 4 | ||
| Main Bearing Cap, crankshaft -------------------------------- | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| Bearing Cap, connecting rod | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| Crankshaft | ||
| Crankshaft Gear---------- | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| Vibration Damper, Crankshaft -------------------------------- | ||
| Flywheel-- | ||
| Camshaft-- | ||
| ··Adjusting Screw, valve clearance, Lock Screw | ||
| Rocker Arm Shaft, valve train ------------------------------- | ||
| ··Rocker Arm Bridge | ||
| Drive gear - Camshaft---- | ||
| Timing Case-------------- | ||
| Fuel Pump- | ||
| ··Fuel Pump, Gear wheel | ||
| Injector Nozzle---------- | ||
| ····Injector Holder | ||
| Oil Pump-- | ||
| ··Cover | ||
| ··Gear wheel | ||
| Oil Pan--- | ||
| ··Oil Drain Plug, oil pan |
Gain access
Enginedesk contains rich-data for parts and engines. The service is particulary useful for engine rebuilders and maintenance shops.
You can browse all information online. To get access to the technical data and parts information we provide the following options:
- Anytime 'all access' € 25,- * per month.
- Anytime 'all access' € 250,- * yearly.
* Excluding sales tax (21%)
Parts manufacturer
Reach thousands of remanufacturing companies. Promote your aftermarket parts and services world wide.
Please contact Enginedesk via info@enginedesk.com.
