Technical Data - SKODA AGP
Manufacturer SKODA
AGP - I - SOHC/OHC
| Engine Type | AGP |
| Fuel Supply System | I |
| Note | SOHC/OHC |
| Cc | 1896 |
| Number of Cylinders | 4 |
| Bore Ø | 79.50 |
| Stroke | 95.50 |
| KW | 50 |
| Compression | 22.5 |
| KBA No. (Germany) | 4114371 |
| Type Mines | 905A3C |
| Technical Information Number | Technical Data | Information |
|---|---|---|
| ····Engine Code | ||
| Compression-------------- | ||
| ····Compression - Ratio | ||
| ····Compression - Pressure [bar] | ||
| ····Cylinder - Differential pressure | ||
| ····Wear limitation | ||
| Refs------ | ||
| ····Idle, min. | ||
| ····Idle, Max. | ||
| ····RPM, Max. | ||
| Exhaust Gas, value------- | ||
| Oil Pressure------------- | ||
| ····Status (Operating Mode / Cold Check) | ||
| ····Idle, min. | ||
| ····Rated Capacity | ||
| Thermostat | ||
| ····Thermostat, Opening Temperature | ||
| Ignition Timing---------- | ||
| ····Ignition System | ||
| Ignition - Row----------- | ||
| ····Ignition Point, Static / Dynamic | ||
| injection pump----------- | ||
| ··Injection - Stage 1 => x | ||
| ··Pressure, Fuel injection | ||
| ····Min. | ||
| =<>= | ||
| General Information - Cylinder Head ------------------------- | ||
| ··Cylinder Head - Height | ||
| ··Height (Min.) - Machined | ||
| ··warpage (value) - Cylinder Head | ||
| ····Wear limitation | ||
| ··Thickness, Gasket | ||
| ··Cylinder Head Gasket, Markings | ||
| ··Cylinder Head Gasket, Markings | ||
| ··Cylinder Head Gasket, Markings | ||
| ··Cylinder Head Gasket, Markings | ||
| ····1st Oversize | ||
| ····2nd Oversize | ||
| ····3rd Oversize | ||
| ··Piston Crown Clearance -/+ | ||
| ····1st Oversize | ||
| ····2nd Oversize | ||
| ····3rd Oversize | ||
| Valves---- | ||
| ··Valve Clearance [mm] | ||
| ··Valve Actuation, Setting | ||
| ····Inlet / Open (° before TDC) | ||
| ····Inlet / Closed (° after BDC) | ||
| ····Exhaust / Open (° before BDC) | ||
| ····Exhaust / Closed (° after TDC) | ||
| ··Valve Head Diameter [D] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valves - Length (L) | ||
| ····Inlet - New Part | ||
| ····Exhaust - New Part | ||
| ··Valve stem diameter [d] - Inlet | ||
| ··Valve stem diameter [d] - Exhaust | ||
| ··Valve Seat Angle [°] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valves, Fitted Height | ||
| ··Clearance - Valve Disc => Cylinder Head (Surface) | ||
| ····Inlet | ||
| ····Inlet | ||
| ····Exhaust | ||
| ····Exhaust | ||
| Valve Guides------------- | ||
| ··Inner Diameter - Standard Size | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Sideplay | ||
| ····Measurement | ||
| ····Inlet | ||
| ····Exhaust | ||
| Valve seat | ||
| ··Valve Seat Angle (B) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Adaptation - Angle (B1) | ||
| ····Inlet | ||
| ··Valve Seat - Measurement (A) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Seat - Diameter (D) | ||
| ····Inlet | ||
| ····Exhaust | ||
| Camshaft-- | ||
| ··Camshaft, Code | ||
| ··Camshaft, Code | ||
| ··Camshaft, Code | ||
| ··Clearance, Radial - Camshaft Bushes | ||
| ····Wear limitation | ||
| ··Clearance, Axial - Camshaft Bushes | ||
| ····Wear limitation | ||
| ··Centering - Camshaft (Tolerance) | ||
| ····Wear limitation | ||
| =<>= | ||
| General Information - Engine Block | ||
| Cylinder Sleeve---------- | ||
| ··Bore | ||
| ··Bore | ||
| ····Standard Size | ||
| ····1st Oversize | ||
| ····2nd Oversize | ||
| Piston---- | ||
| ··Diameter - Piston | ||
| ····Standard Size | ||
| ····1st Oversize | ||
| ····2nd Oversize | ||
| ····Measurement (Position) | ||
| Piston Ring Set---------- | ||
| ··Piston Ring, Groove | ||
| ··1st Piston Ring, Lock - Clearance (Compression) | ||
| ····Wear limitation | ||
| ··2nd Piston Ring, Lock - Clearance (Compression) | ||
| ····Wear limitation | ||
| ··Piston Ring, Lock - Clearance (Oil Trap) | ||
| ····Wear limitation | ||
| ··1st Piston Ring, Height - Clearance (Compression) | ||
| ····Wear limitation | ||
| ··2nd Piston Ring, Height - Clearance (Compression) | ||
| ····Wear limitation | ||
| ··Piston Ring, Height - Clearance (Oil Trap) | ||
| ····Wear limitation | ||
| Connecting Rod----------- | ||
| ··Clearance, Radial - Big End Bearing | ||
| ····Wear limitation | ||
| ····Wear limitation | ||
| ··Clearance, Axial - Big End Bearing | ||
| ··Diameter, Bearing Journal - Connecting Rod | ||
| ····Standard Size | ||
| ····1st Undersize | ||
| ····2nd Undersize | ||
| ····3rd Undersize | ||
| Crankshaft | ||
| ··Number of bearings | ||
| ··Diameter, Bearing Journal - Crankshaft (Standard Size) | ||
| ··Diameter, Bearing Journal - Crankshaft (1st Undersize) | ||
| ··Diameter, Bearing Journal - Crankshaft (2nd Undersize) | ||
| ··Diameter, Bearing Journal - Crankshaft (3rd Undersize) | ||
| ··Clearance - Main Bearing, crankshaft | ||
| ····Wear limitation | ||
| ··Bearing clearance - Axial Bearing | ||
| ····Wear limitation | ||
| =<>= | ||
| Engine Timing Control | ||
| Valve Cover-------------- | ||
| Cylinder Head Bolts------ | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| ····Stage 3 | ||
| ····Stage 4 | ||
| Main Bearing Cap, crankshaft -------------------------------- | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| Bearing Cap, connecting rod | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| Crankshaft | ||
| Crankshaft Gear---------- | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| Flywheel-- | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| Camshaft, Bearing Cap---- | ||
| Drive gear - Camshaft---- | ||
| Water Pump | ||
| Fuel Pump- | ||
| ··Drive gear - Fuel Pump | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| Oil Pump-- | ||
| ··Oil atomizer | ||
| Oil Pan--- | ||
| ··Oil Drain Plug, oil pan | ||
| Exhaust Manifold--------- | ||
| Intake Manifold---------- |
Gain access
Enginedesk contains rich-data for parts and engines. The service is particulary useful for engine rebuilders and maintenance shops.
You can browse all information online. To get access to the technical data and parts information we provide the following options:
- Anytime 'all access' € 25,- * per month.
- Anytime 'all access' € 250,- * yearly.
* Excluding sales tax (21%)
Parts manufacturer
Reach thousands of remanufacturing companies. Promote your aftermarket parts and services world wide.
Please contact Enginedesk via info@enginedesk.com.
