Technical Data - VOLVO TD 162 FL (->1991)
Manufacturer VOLVO
TD 162 FL (->1991) - T - Turbo, LLK
| Engine Type | TD 162 FL (->1991) |
| Fuel Supply System | T |
| Note | Turbo, LLK |
| Cc | 16120 |
| Number of Cylinders | 6 |
| Bore Ø | 144.00 |
| Stroke | 165.00 |
| KW | 342 |
| Compression | 15 |
| KBA No. (Germany) | 4114371 |
| Type Mines | 905A3C |
| Technical Information Number | Technical Data | Information |
|---|---|---|
| Charger--- | ||
| ··Type | ||
| ····Intercooler, charger | ||
| ····Turbocharger - Pressure (Max.) | ||
| Compression-------------- | ||
| ····Compression - Ratio | ||
| ····Compression - Pressure [bar] | ||
| Refs------ | ||
| ····Idle, min. | ||
| Oil Pressure------------- | ||
| ····Status (Operating Mode / Cold Check) | ||
| ····Idle, min. | ||
| ····Min. | ||
| ····Rated Capacity | ||
| Thermostat | ||
| ····Thermostat, Opening Temperature | ||
| injection pump----------- | ||
| ··Injection - Stage 1 => x | ||
| ····Injection (Point - ° before TDC) | ||
| ··Pressure, Fuel injection | ||
| ····New Part | ||
| ····Min. | ||
| Pressure, Radiator Cap--- | ||
| ····Opening Pressure | ||
| =<>= | ||
| ··Piston Crown Clearance -/+ | ||
| Valves---- | ||
| ··Valve Clearance - Cold Check [mm] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Head Diameter [D] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valves - Length (L) | ||
| ····Inlet - New Part | ||
| ····Exhaust - New Part | ||
| ··Valve stem diameter [d] - Inlet | ||
| ····Material | ||
| ····Standard Size | ||
| ··Valve stem diameter [d] - Exhaust | ||
| ····Material | ||
| ····Standard Size | ||
| ··Valve Seat Angle [°] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valves, Fitted Height | ||
| ····Inlet | ||
| ····Exhaust | ||
| Valve Guides------------- | ||
| ··Material | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Guide - Length [mm] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Inner Diameter - Standard Size | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Outer Diameter - Standard Size | ||
| ····Inlet | ||
| ····Exhaust | ||
| =<>= | ||
| =<>= | ||
| General Information - Engine Block | ||
| ··Cylinder Sleeve Protrusion | ||
| Piston---- | ||
| ··Piston Crown Protrusion -/+ (Piston => Surface, Cylinder Head) | ||
| Connecting Rod----------- | ||
| ··Bore - Holder, Connecting Rod (Big End Bearing) | ||
| ··Diameter, Bearing Journal - Connecting Rod | ||
| ····Standard Size | ||
| Crankshaft | ||
| ··Diameter, Bearing Journal - Crankshaft (Standard Size) | ||
| ··Housing Diameter - Main Bearings | ||
| =<>= | ||
| =<>= | ||
| Cylinder Head------------ | ||
| Cylinder Head------------ | ||
| Cylinder Head Bolts------ | ||
| Cylinder Head Bolts------ | ||
| ····Stage 1 | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| ····Stage 2 | ||
| ····Stage 3 | ||
| ····Stage 3 | ||
| ····Stage 4 | ||
| ····Stage 4 | ||
| ····Stage 5 | ||
| ····Stage 5 | ||
| ····Retouching | ||
| ····Retouching | ||
| Main Bearing Cap, crankshaft -------------------------------- | ||
| Main Bearing Cap, crankshaft -------------------------------- | ||
| Bearing Cap, connecting rod | ||
| Bearing Cap, connecting rod | ||
| Crankshaft | ||
| Crankshaft | ||
| Vibration Damper, Crankshaft -------------------------------- | ||
| Vibration Damper, Crankshaft -------------------------------- | ||
| Flywheel-- | ||
| Flywheel-- | ||
| Rocker Arm Shaft, valve train ------------------------------- | ||
| Rocker Arm Shaft, valve train ------------------------------- | ||
| ··Rocker Arm Bridge | ||
| ··Rocker Arm Bridge | ||
| Drive gear - Camshaft---- | ||
| Drive gear - Camshaft---- | ||
| Timing Case-------------- | ||
| Timing Case-------------- | ||
| ··intermediate gear, Timing Case | ||
| ··intermediate gear, Timing Case | ||
| Fuel Pump- | ||
| Fuel Pump- | ||
| ··Fuel Pump, Gear wheel | ||
| ··Fuel Pump, Gear wheel | ||
| Injector Nozzle---------- | ||
| Injector Nozzle---------- | ||
| ····Injector Holder | ||
| ····Injector Holder |
Gain access
Enginedesk contains rich-data for parts and engines. The service is particulary useful for engine rebuilders and maintenance shops.
You can browse all information online. To get access to the technical data and parts information we provide the following options:
- Anytime 'all access' € 25,- * per month.
- Anytime 'all access' € 250,- * yearly.
* Excluding sales tax (21%)
Parts manufacturer
Reach thousands of remanufacturing companies. Promote your aftermarket parts and services world wide.
Please contact Enginedesk via info@enginedesk.com.
