Technical Data - FORD EUROPE EDDA
Manufacturer FORD EUROPE
EDDA - I -
| Engine Type | EDDA |
| Fuel Supply System | I |
| Note |
| Cc | 1988 |
| Number of Cylinders | 4 |
| Bore Ø | 84.80 |
| Stroke | 88.00 |
| KW | 96 |
| Compression | 10 |
| KBA No. (Germany) | 4114371 |
| Type Mines | 905A3C |
| Technical Information Number | Technical Data | Information |
|---|---|---|
| ····Engine Code | ||
| Compression-------------- | ||
| ····Compression - Ratio | ||
| Refs------ | ||
| ····Idle, min. | ||
| ····Idle, Max. | ||
| ····RPM, Max. | ||
| Exhaust Gas, value------- | ||
| Oil Pressure------------- | ||
| ····Idle, min. | ||
| ····Rated Capacity | ||
| Thermostat | ||
| ····Thermostat, Opening Temperature | ||
| Ignition Timing---------- | ||
| ····Ignition System | ||
| Ignition - Row----------- | ||
| =<>= | ||
| General Information - Cylinder Head ------------------------- | ||
| ··Roughness cylinder head fitting face | ||
| ··Cylinder Head - Height | ||
| ··warpage (value) - Cylinder Head | ||
| ····Wear limitation | ||
| Valves---- | ||
| ··Valve Clearance [mm] | ||
| ····Operating Mode / Cold Check | ||
| ····Inlet | ||
| ····Exhaust | ||
| Valve Guides------------- | ||
| ··Clearance - Valve => Valve Guides | ||
| ····Inlet | ||
| ····Exhaust | ||
| Camshaft-- | ||
| ··Diameter, Bearing Journal - Camshaft (Standard Size) | ||
| ··Clearance, Radial - Camshaft Bushes | ||
| ··Clearance, Axial - Camshaft Bushes | ||
| =<>= | ||
| General Information - Engine Block | ||
| ··Bore - Holder, Main Bearings (Engine Block) | ||
| Cylinder Sleeve---------- | ||
| ··Bore | ||
| ··Bore | ||
| ··Bore | ||
| ··Bore | ||
| ··Bore | ||
| Piston---- | ||
| ··Diameter - Piston | ||
| ··Diameter - Piston | ||
| ··Diameter - Piston | ||
| ··Diameter - Piston | ||
| ··Clearance - Piston | ||
| Gudgeon Pin-------------- | ||
| ··Length [mm] - Gudgeon Pin | ||
| ··Diameter - Gudgeon Pin | ||
| ··Diameter - Gudgeon Pin | ||
| ··Clearance, Radial - Gudgeon Pin | ||
| Piston Ring Set---------- | ||
| ··Piston Ring, Groove | ||
| ··1st Piston Ring, Lock - Clearance (Compression) | ||
| ··2nd Piston Ring, Lock - Clearance (Compression) | ||
| ··Piston Ring, Lock - Clearance (Oil Trap) | ||
| Connecting Rod----------- | ||
| ··Bore - Holder, Connecting Rod (Small End Bushes) | ||
| ··Bore - Holder, Connecting Rod (Big End Bearing) | ||
| ··Inner Diameter - Big End Bearing | ||
| ··Clearance, Radial - Big End Bearing | ||
| ··Clearance, Axial - Big End Bearing | ||
| ··Diameter, Bearing Journal - Connecting Rod | ||
| Crankshaft | ||
| ··Number of bearings | ||
| ··Diameter, Bearing Journal - Crankshaft (Standard Size) | ||
| ··Diameter, Bearing Journal - Crankshaft (Standard Size) | ||
| ··Clearance - Main Bearing, crankshaft | ||
| ··Bearing clearance - Axial Bearing | ||
| Main Bearing scales, crankshaft ----------------------------- | ||
| =<>= | ||
| Valve Cover-------------- | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| Cylinder Head Bolts------ | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| ····Stage 3 | ||
| Main Bearing Cap, crankshaft -------------------------------- | ||
| Mounting Bracket Crankshaft | ||
| Bearing Cap, connecting rod | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| Crankshaft | ||
| ····Retainer Ring, Shaft Oil Seal (Rear) | ||
| Crankshaft Gear---------- | ||
| ··Knock Sensor | ||
| Sensor, crankshaft pulse- | ||
| Flywheel-- | ||
| Camshaft, Bearing Cap---- | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| Drive gear - Camshaft---- | ||
| Timing Case-------------- | ||
| ··Timing Case, Cover | ||
| ····Upper section | ||
| ··V-Belt, Pulley | ||
| ··Timing Belt Tensioner | ||
| ··Guide Pulley | ||
| ····Lower Section | ||
| ····Upper section | ||
| Alternator | ||
| Spark Plug | ||
| Ignition Coil | ||
| Starter--- | ||
| Water Pump | ||
| ····Water Pump Pulley | ||
| Cooling System----------- | ||
| ··Thermostat Housing | ||
| Fuel Pump- | ||
| ··Fuel Line | ||
| injection pump----------- | ||
| ··Attachment Panel - For Cylinder block | ||
| ··Injection Pipe | ||
| ··Bracket | ||
| ··Bracket | ||
| Oil Pump-- | ||
| ··Oil Drain Plug - Oil Pipe | ||
| ··Oil Pressure Switch | ||
| Oil Pan--- | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| ··Oil Drain Plug, oil pan | ||
| ··Pipe, crankcase breather | ||
| ··Bracket | ||
| ··Oil Strainer | ||
| Exhaust Manifold--------- | ||
| Exhaust Manifold--------- | ||
| Intake Manifold---------- | ||
| Intake Manifold---------- |
Gain access
Enginedesk contains rich-data for parts and engines. The service is particulary useful for engine rebuilders and maintenance shops.
You can browse all information online. To get access to the technical data and parts information we provide the following options:
- Anytime 'all access' € 25,- * per month.
- Anytime 'all access' € 250,- * yearly.
* Excluding sales tax (21%)
Parts manufacturer
Reach thousands of remanufacturing companies. Promote your aftermarket parts and services world wide.
Please contact Enginedesk via info@enginedesk.com.
