Technical Data - HONDA D14-A1
Manufacturer HONDA
D14-A1 - C -
| Engine Type | D14-A1 |
| Fuel Supply System | C |
| Note |
| Cc | 1396 |
| Number of Cylinders | 4 |
| Bore Ø | 75.00 |
| Stroke | 79.00 |
| KW | 66 |
| Compression | 9.30 |
| KBA No. (Germany) | 4114371 |
| Type Mines | 905A3C |
| Technical Information Number | Technical Data | Information |
|---|---|---|
| ····Engine Code | ||
| Compression-------------- | ||
| ····Compression - Pressure [bar] | ||
| ····Cylinder - Differential pressure | ||
| ····Wear limitation | ||
| Refs------ | ||
| ····Idle, min. | ||
| ····Manual Transmission | ||
| ····Automatic Transmission | ||
| Exhaust Gas, value------- | ||
| ····CO Measurement, Idle | ||
| ····CO2 Measurement, Idle [%] | ||
| ····HC Measurement, Idle | ||
| ····NOx Measurement, Idle | ||
| Oil Pressure------------- | ||
| ····Status (Operating Mode / Cold Check) | ||
| ····Idle, min. | ||
| ····Rated Capacity | ||
| Thermostat | ||
| ····Thermostat, Opening Temperature | ||
| Ignition Timing---------- | ||
| ····Ignition System | ||
| Ignition - Row----------- | ||
| ····Ignition Point, Static / Dynamic | ||
| =<>= | ||
| ··Cylinder Head - Height | ||
| ····New Part | ||
| ····Min. | ||
| ··warpage (value) - Cylinder Head | ||
| ····Wear limitation | ||
| Valves---- | ||
| ··Valve Clearance [mm] | ||
| ····Operating Mode / Cold Check | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Head Diameter [D] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valves - Length (L) | ||
| ····Inlet - New Part | ||
| ····Exhaust - New Part | ||
| ··Valve stem diameter [d] - Inlet | ||
| ····Standard Size | ||
| ····Wear limitation | ||
| ··Valve stem diameter [d] - Exhaust | ||
| ····Standard Size | ||
| ····Wear limitation | ||
| ··Valve Disc, Thickness (t) | ||
| ····Inlet | ||
| ····Wear limitation - Inlet | ||
| ····Exhaust | ||
| ····Wear limitation - Outlet | ||
| ··Valve - Protrusion (+/-) | ||
| ····Fitting Position | ||
| ····Inlet | ||
| ····Wear limitation - Inlet | ||
| ····Exhaust | ||
| ····Wear limitation - Outlet | ||
| Valve Spring------------- | ||
| ··Tolerance - Vertical (s) | ||
| ··Valve Spring - Length (Load/Empty) | ||
| ····Inlet - inner | ||
| ····Wear limitation - Inlet (Inner) | ||
| ··Diameter - Spring, Material | ||
| ····Inlet | ||
| ····Wear limitation - Inlet | ||
| ····Exhaust | ||
| ····Wear limitation - Outlet | ||
| Valve Guides------------- | ||
| ··Temperature Range [°C] - Press-out | ||
| ··Fitted Height | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Inner Diameter - Standard Size | ||
| ····Inlet | ||
| ····Wear limitation - Inlet | ||
| ····Exhaust | ||
| ····Wear limitation - Outlet | ||
| ··Clearance - Valve => Valve Guides | ||
| ··Clearance - Valve => Valve Guides | ||
| ····Inlet | ||
| ····Inlet | ||
| ····Wear limitation - Inlet | ||
| ····Wear limitation - Inlet | ||
| ····Exhaust | ||
| ····Exhaust | ||
| ····Wear limitation - Outlet | ||
| ····Wear limitation - Outlet | ||
| Valve seat | ||
| ··Valve Seat Angle (B) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Adaptation - Angle (B1) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Adaptation - Angle (B2) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Seat - Measurement (A) | ||
| ····Inlet | ||
| ····Wear limitation - Inlet | ||
| ····Exhaust | ||
| ····Wear limitation - Outlet | ||
| Valve Actuation--------- | ||
| ··Rocker Arm Shaft, valve train | ||
| ····Fitting Position | ||
| ··Clearance, Radial - Rocker | ||
| ····Wear limitation - Outlet | ||
| Camshaft-- | ||
| ··Clearance, Radial - Camshaft Bushes | ||
| ····Wear limitation | ||
| ··Clearance, Axial - Camshaft Bushes | ||
| ····Wear limitation | ||
| ··Centering - Camshaft (Tolerance) | ||
| ····Wear limitation | ||
| ··Cam Lobe Height (Total) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ····Exhaust | ||
| =<>= | ||
| Cylinder Sleeve---------- | ||
| ··Bore | ||
| ··Bore | ||
| ····Standard Size | ||
| ····Wear limitation | ||
| ····1st Oversize | ||
| ····2nd Oversize | ||
| ··Measurement - Oval, Bore (Cylinder Sleeve) | ||
| ····Wear limitation | ||
| ··Measurement - Conical | ||
| ····Wear limitation | ||
| Piston---- | ||
| ··Diameter - Piston | ||
| ····Standard Size | ||
| ····Wear limitation | ||
| ····1st Oversize | ||
| ····2nd Oversize | ||
| ····Measurement (Position) | ||
| Gudgeon Pin-------------- | ||
| ··Clearance, Radial - Gudgeon Pin | ||
| ····Clearance, Radial - Piston Rod / Piston | ||
| ····Wear limitation | ||
| Piston Ring Set---------- | ||
| ··Piston Ring, Groove | ||
| ··1st Piston Ring, Lock - Clearance (Compression) | ||
| ····Wear limitation | ||
| ··2nd Piston Ring, Lock - Clearance (Compression) | ||
| ····Wear limitation | ||
| ··Piston Ring, Lock - Clearance (Oil Trap) | ||
| ····Wear limitation | ||
| ··1st Piston Ring, Height - Clearance (Compression) | ||
| ····Wear limitation | ||
| ··2nd Piston Ring, Height - Clearance (Compression) | ||
| ····Wear limitation | ||
| Connecting Rod----------- | ||
| ··Bore - Holder, Connecting Rod (Big End Bearing) | ||
| ··Clearance, Radial - Big End Bearing | ||
| ··Clearance, Radial - Big End Bearing | ||
| ····Wear limitation | ||
| ····Wear limitation | ||
| ····Wear limitation | ||
| ··Clearance, Axial - Big End Bearing | ||
| ··Diameter, Bearing Journal - Connecting Rod | ||
| ··Bearing Journal, Connecting Rod - Tolerance (Oval) | ||
| ····Bearing Journal, Connecting Rod - Oval (Max.) | ||
| ····Wear limitation | ||
| ··Bearing Journal, Connecting Rod - Conical (Max.) | ||
| ····Wear limitation | ||
| Crankshaft | ||
| ··Number of bearings | ||
| ··Centering - Crankshaft (Tolerance) | ||
| ····Wear limitation | ||
| ··Diameter, Bearing Journal - Crankshaft (Standard Size) | ||
| ··Bearing Journal, Crankshaft - Conical (Max.) | ||
| ····Wear limitation | ||
| ··Bearing Journal, Crankshaft - Oval (Max.) | ||
| ····Wear limitation | ||
| ··Clearance - Main Bearing, crankshaft | ||
| ····Wear limitation | ||
| ··Bearing clearance - Axial Bearing | ||
| ····Wear limitation | ||
| Cooling System----------- | ||
| ··Type | ||
| ··Clearance, Axial - Outer, Rotor (Housing, Oil Pump) | ||
| ··Clearance - Outer, Rotor => Inside, Rotor | ||
| ····Wear limitation | ||
| ··Clearance - Outer, Rotor => Housing, Oil Pump | ||
| ····Wear limitation | ||
| Timing Gear, Kit (Control)- | ||
| ··Clearance - Gear wheel (Tooth Pitch) | ||
| ····Wear limitation | ||
| =<>= | ||
| Engine Timing Control | ||
| Valve Cover-------------- | ||
| Cylinder Head Bolts------ | ||
| ····Stage 1 | ||
| Main Bearing Cap, crankshaft -------------------------------- | ||
| Bearing Cap, connecting rod | ||
| Crankshaft | ||
| Crankshaft Gear---------- | ||
| Flywheel-- | ||
| Driver Plate------------- | ||
| Camshaft-- | ||
| ··Adjusting Screw, valve clearance, Lock Screw | ||
| Camshaft, Bearing Cap---- | ||
| Drive gear - Camshaft---- | ||
| Timing Case-------------- | ||
| ··Timing Case, Cover | ||
| ··Timing Belt Tensioner | ||
| Oil Pump-- | ||
| Oil Pan--- | ||
| ··Oil Drain Plug, oil pan | ||
| Exhaust Manifold--------- | ||
| Intake Manifold---------- |
Gain access
Enginedesk contains rich-data for parts and engines. The service is particulary useful for engine rebuilders and maintenance shops.
You can browse all information online. To get access to the technical data and parts information we provide the following options:
- Anytime 'all access' € 25,- * per month.
- Anytime 'all access' € 250,- * yearly.
* Excluding sales tax (21%)
Parts manufacturer
Reach thousands of remanufacturing companies. Promote your aftermarket parts and services world wide.
Please contact Enginedesk via info@enginedesk.com.
