Technical Data - MERCEDES 10 LTR. ==> OM402 LA [Euro 1]
Manufacturer MERCEDES 10 LTR. ==>
OM402 LA [Euro 1] - T - V-Motor
| Engine Type | OM402 LA [Euro 1] |
| Fuel Supply System | T |
| Note | V-Motor |
| Cc | 12763 |
| Number of Cylinders | 8 |
| Bore Ø | 125.00 |
| Stroke | 130.00 |
| KW | 280 |
| Compression | 16.75 |
| KBA No. (Germany) | 4114371 |
| Type Mines | 905A3C |
| Technical Information Number | Technical Data | Information |
|---|---|---|
| Engine - Manufacturer---- | ||
| ··Type | ||
| ····Engine Output kW [HP] | ||
| ····Number of Cylinders | ||
| ····Engine design (2 ~ 4 stroke) | ||
| ····Displacement (exact) [cc] | ||
| ····Stroke [mm] | ||
| ····Bore Ø [mm] | ||
| ····Cooling System | ||
| ····Fuel (consumption - Specification) | ||
| Charger--- | ||
| ··Type | ||
| ····Turbocharger - Pressure (Max.) | ||
| Compression-------------- | ||
| ····Compression - Ratio | ||
| ····Compression - Pressure [bar] | ||
| ····Wear limitation | ||
| Refs------ | ||
| ····Idle, min. | ||
| Oil Pressure------------- | ||
| ····Status (Operating Mode / Cold Check) | ||
| ····Idle, min. | ||
| ····Min. | ||
| Thermostat | ||
| ····Thermostat, Opening Temperature | ||
| Ignition Timing---------- | ||
| Ignition Timing---------- | ||
| ····Ignition System | ||
| injection pump----------- | ||
| ··Type | ||
| ····Injector Holder | ||
| ····Injector Nozzle | ||
| ··Injection - Stage 1 => x | ||
| ····Fuel Pre-supply - ° before TDC | ||
| ····Injection (Point - ° before TDC) | ||
| ··Pressure, Fuel injection | ||
| ····New Part | ||
| ····Min. | ||
| Pressure, Radiator Cap--- | ||
| ····Opening Pressure | ||
| =<>= | ||
| ··Cylinder Head - Height | ||
| ····Cylinder Head - Height (D) | ||
| ····Min. | ||
| ··Piston Crown Clearance -/+ | ||
| Valves---- | ||
| ··Valve Clearance - Cold Check [mm] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Head Diameter [D] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valves - Length (L) | ||
| ····Inlet - New Part | ||
| ····Exhaust - New Part | ||
| ··Valve stem diameter [d] - Inlet | ||
| ····Material | ||
| ····Standard Size | ||
| ··Valve stem diameter [d] - Exhaust | ||
| ····Material | ||
| ····Standard Size | ||
| ··Valve Seat Angle [°] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Clearance - Valve Disc => Cylinder Head (Surface) | ||
| ····Inlet | ||
| ····Exhaust | ||
| Valve Guides------------- | ||
| ··Material | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Guide - Length [mm] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Inner Diameter - Standard Size | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Outer Diameter - Standard Size | ||
| ····Inlet | ||
| ····Exhaust | ||
| =<>= | ||
| General Information - Engine Block | ||
| ··Cylinder Sleeve Protrusion | ||
| Cylinder Sleeve---------- | ||
| Piston---- | ||
| ··Piston Crown Protrusion -/+ (Piston => Surface, Cylinder Head) | ||
| Connecting Rod----------- | ||
| ··Bore - Holder, Connecting Rod (Big End Bearing) | ||
| ··Clearance, Radial - Big End Bearing | ||
| ··Diameter, Bearing Journal - Connecting Rod | ||
| ····Standard Size | ||
| Crankshaft | ||
| ··Diameter, Bearing Journal - Crankshaft (Standard Size) | ||
| ··Housing Diameter - Main Bearings | ||
| ··Clearance - Main Bearing, crankshaft | ||
| =<>= | ||
| Cylinder Head------------ | ||
| Cylinder Head Bolts------ | ||
| ····Replace - Bolts | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| ····Stage 3 | ||
| ····Stage 4 | ||
| ····Stage 5 | ||
| ····Stage 6 | ||
| ····Retouching | ||
| ····Bolt Length - Max. | ||
| Main Bearing Cap, crankshaft -------------------------------- | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| ····Stage 3 | ||
| ····Stage 4 | ||
| ····Other - Bolt | ||
| Bearing Cap, connecting rod | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| Crankshaft | ||
| Crankshaft Gear---------- | ||
| Vibration Damper, Crankshaft -------------------------------- | ||
| Flywheel-- | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| Stabilizer, Weight------- | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| Rocker Arm Shaft, valve train ------------------------------- | ||
| ··Rocker Arm Bridge | ||
| Timing Case-------------- | ||
| ··intermediate gear | ||
| Injector Nozzle---------- | ||
| ····Injector Holder |
Gain access
Enginedesk contains rich-data for parts and engines. The service is particulary useful for engine rebuilders and maintenance shops.
You can browse all information online. To get access to the technical data and parts information we provide the following options:
- Anytime 'all access' € 25,- * per month.
- Anytime 'all access' € 250,- * yearly.
* Excluding sales tax (21%)
Parts manufacturer
Reach thousands of remanufacturing companies. Promote your aftermarket parts and services world wide.
Please contact Enginedesk via info@enginedesk.com.
