Technical Data - MINI W10 (B16A)
Manufacturer MINI
W10 (B16A) - I -
| Engine Type | W10 (B16A) |
| Fuel Supply System | I |
| Note |
| Cc | 1598 |
| Number of Cylinders | 4 |
| Bore Ø | 77.00 |
| Stroke | 85.80 |
| KW | 66 |
| Compression | 10.6 |
| KBA No. (Germany) | 4114371 |
| Type Mines | 905A3C |
| Technical Information Number | Technical Data | Information |
|---|---|---|
| Engine - Manufacturer---- | ||
| ····Construction Year (From - To) | ||
| ····Engine Output kW [HP] | ||
| ····Number of Cylinders | ||
| ····Engine Code | ||
| ····Displacement (exact) [cc] | ||
| Compression-------------- | ||
| ····Compression - Ratio | ||
| ····Compression - Pressure [bar] | ||
| Exhaust Gas, value------- | ||
| ····Idle | ||
| ····CO Measurement, Idle | ||
| ····CO Measurement (Catalytic Converter => ) | ||
| ····Oil Temperature (CO Measurement) - °C | ||
| ····HC Measurement, Idle | ||
| ····Idle RPM Increase | ||
| ····CO Measurement, Idle RPM Increase | ||
| ····Lambda Value, Idle RPM Increase | ||
| Oil Pressure------------- | ||
| ····Status (Operating Mode / Cold Check) | ||
| ····Idle, min. | ||
| ····Min. | ||
| ····Rated Capacity | ||
| Spark Plug | ||
| ··Type | ||
| Fuel Supply-------------- | ||
| ··Type | ||
| ····Fuel Supply System | ||
| ····Air Flow Sensor | ||
| Feed pump - Fuel--------- | ||
| ····Fuel Pressure (system) | ||
| Ignition Timing---------- | ||
| ····Ignition System | ||
| ····Pulse Generator | ||
| Ignition - Row----------- | ||
| ····Ignition Point (° before TDC) | ||
| ····premature ignition [degree] / RPM | ||
| =<>= | ||
| General Information - Cylinder Head ------------------------- | ||
| ··Tester, pneumatic pressure - Cylinder Head | ||
| Valves---- | ||
| ··Valve Clearance [mm] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valves - Length (L) | ||
| ····Inlet - New Part | ||
| ····Exhaust - New Part | ||
| ··Valve stem diameter [d] - Inlet | ||
| ····Standard Size | ||
| ··Valve stem diameter [d] - Exhaust | ||
| ····Standard Size | ||
| ··Valve Seat Angle [°] | ||
| ····Inlet | ||
| ····Exhaust | ||
| Valve Guides------------- | ||
| ··Inner Diameter - Standard Size | ||
| ··Clearance - Valve => Valve Guides | ||
| ····Inlet | ||
| ····Wear limitation - Inlet | ||
| ····Exhaust | ||
| ····Wear limitation - Outlet | ||
| Valve seat | ||
| ··Valve seat - Width | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Seat Angle (B) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Adaptation - Angle (B1) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Adaptation - Angle (B2) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Seat - Outer Diameter, Standard Size | ||
| ····Inlet 1 | ||
| ····Exhaust | ||
| Camshaft-- | ||
| ··Diameter, Bearing Journal - Camshaft (Standard Size) | ||
| ··Clearance, Radial - Camshaft Bushes | ||
| ····Wear limitation - Inlet | ||
| ··Clearance, Axial - Camshaft Bushes | ||
| ····Wear limitation | ||
| =<>= | ||
| Cylinder Sleeve---------- | ||
| ··Bore | ||
| ····Standard Size | ||
| ··Measurement - Oval, Bore (Cylinder Sleeve) | ||
| ····Standard Size | ||
| ··Measurement - Conical | ||
| ····Standard Size | ||
| Piston---- | ||
| ··Diameter - Piston | ||
| ····Standard Size | ||
| ··Clearance - Piston | ||
| ····Wear limitation | ||
| Piston Ring Set---------- | ||
| ··Piston Ring, Groove | ||
| ··1st Piston Ring, Lock - Clearance (Compression) | ||
| ····Wear limitation | ||
| ··2nd Piston Ring, Lock - Clearance (Compression) | ||
| ····Wear limitation | ||
| ··Piston Ring, Lock - Clearance (Oil Trap) | ||
| ····Wear limitation | ||
| ··1st Piston Ring, Height - Clearance (Compression) | ||
| ··2nd Piston Ring, Height - Clearance (Compression) | ||
| ··Piston Ring, Height - Clearance (Oil Trap) | ||
| Connecting Rod----------- | ||
| ··Clearance, Radial - Big End Bearing | ||
| ····Wear limitation | ||
| ··Diameter, Bearing Journal - Connecting Rod | ||
| ····Standard Size | ||
| ··Small End Bushes | ||
| ····Inner Diameter | ||
| ····Wear limitation | ||
| ····Clearance, Radial - Small End Bush / Gudgeon Pin | ||
| Crankshaft | ||
| ··Diameter, Bearing Journal - Crankshaft (Standard Size) | ||
| ··Clearance - Main Bearing, crankshaft | ||
| ····Wear limitation | ||
| ··Bearing clearance - Axial Bearing | ||
| ····Wear limitation | ||
| =<>= | ||
| Valve Cover-------------- | ||
| Cylinder Head------------ | ||
| Cylinder Head Bolts------ | ||
| ····Replace - Bolts | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| ····Retouching | ||
| ····Other - Bolt | ||
| Main Bearing Cap, crankshaft -------------------------------- | ||
| ····Replace - Bolts | ||
| ····Bolt, Main Bearing Cap | ||
| ····Other - Bolt | ||
| Bearing Cap, connecting rod | ||
| ····Replace - Bolts | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| Crankshaft | ||
| Cranskhaft Pulley-------- | ||
| Vibration Damper, Crankshaft -------------------------------- | ||
| ··Knock Sensor | ||
| Flywheel-- | ||
| Camshaft, Bearing Cap---- | ||
| Rocker Arm Shaft, valve train ------------------------------- | ||
| Drive gear - Camshaft---- | ||
| Timing Case-------------- | ||
| ··Timing Belt Cover | ||
| ··Timing Chain Tensioner | ||
| ··Guides, timing chain | ||
| ··Timing Belt Tensioner | ||
| ··Guide Pulley | ||
| Spark Plug | ||
| Water Pump | ||
| Cooling System----------- | ||
| ··Thermostat Housing | ||
| Oil Pump-- | ||
| ··Cover | ||
| ··Oil Pressure Switch | ||
| Oil Cooler, engine oil--- | ||
| Oil Pan--- | ||
| ····Bolt | ||
| ··Oil Drain Plug, oil pan | ||
| ··Oil Dipstick - Holder | ||
| ··Oil Filter | ||
| ··Oil Strainer | ||
| Exhaust Manifold--------- | ||
| ··Lambda Sensor | ||
| Intake Manifold---------- | ||
| Turbocompressor--------- | ||
| Clutch Pressure Plate---- |
Gain access
Enginedesk contains rich-data for parts and engines. The service is particulary useful for engine rebuilders and maintenance shops.
You can browse all information online. To get access to the technical data and parts information we provide the following options:
- Anytime 'all access' € 25,- * per month.
- Anytime 'all access' € 250,- * yearly.
* Excluding sales tax (21%)
Parts manufacturer
Reach thousands of remanufacturing companies. Promote your aftermarket parts and services world wide.
Please contact Enginedesk via info@enginedesk.com.
