Technical Data - MITSUBISHI 6A12-2
Manufacturer MITSUBISHI
6A12-2 - I -
| Engine Type | 6A12-2 |
| Fuel Supply System | I |
| Note |
| Cc | 1993 |
| Number of Cylinders | 6 |
| Bore Ø | 78.40 |
| Stroke | 69.00 |
| KW | 110 |
| Compression | 10.00 |
| KBA No. (Germany) | 4114371 |
| Type Mines | 905A3C |
| Technical Information Number | Technical Data | Information |
|---|---|---|
| Compression-------------- | ||
| ····Compression - Ratio | ||
| ····Compression - Pressure [bar] | ||
| ····Wear limitation | ||
| Refs------ | ||
| ····Idle, min. | ||
| ····Idle, Max. | ||
| Exhaust Gas, value------- | ||
| Ignition Timing---------- | ||
| ····Ignition System | ||
| Ignition - Row----------- | ||
| =<>= | ||
| ··Cylinder Head - Height | ||
| ··warpage (value) - Cylinder Head | ||
| ····Measurement Range (Max.) - Machined | ||
| ··warpage - Manifold | ||
| Valves---- | ||
| ··Valve Clearance [mm] | ||
| ··Valve Actuation, Setting | ||
| ··Valve Actuation, Setting | ||
| ····Inlet / Open (° before TDC) | ||
| ····Inlet / Closed (° after BDC) | ||
| ····Inlet / Closed (° after BDC) | ||
| ····Inlet / Closed (° after BDC) | ||
| ····Exhaust / Open (° before BDC) | ||
| ····Exhaust / Open (° before BDC) | ||
| ····Exhaust / Closed (° after TDC) | ||
| ····Exhaust / Closed (° after TDC) | ||
| ··Valves - Length (L) | ||
| ····Inlet - New Part | ||
| ····Wear limitation - Inlet | ||
| ····Exhaust - New Part | ||
| ····Wear limitation - Outlet | ||
| ··Valve stem diameter [d] - Inlet | ||
| ····Standard Size | ||
| ··Valve stem diameter [d] - Exhaust | ||
| ····Standard Size | ||
| ··Valve Disc, Thickness (t) | ||
| ····Inlet | ||
| ····Wear limitation - Inlet | ||
| ····Exhaust | ||
| ····Wear limitation - Outlet | ||
| ··Valve - Protrusion (+/-) | ||
| ····Fitting Position | ||
| ····Fitting Position | ||
| ····Wear limitation - Inlet | ||
| Valve Spring------------- | ||
| ··Tolerance - Vertical (s) | ||
| ··Valve Spring - Length (Load/Empty) | ||
| ····Wear limitation | ||
| ··Diameter - Spring, Material | ||
| ····Wear limitation - Inlet | ||
| ··Min. Length [mm] => Capacitive Load 1 | ||
| Valve Guides------------- | ||
| ··Inner Diameter - Standard Size | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Bore - Holder, Valve Guides (Standard Size) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Bore - Holder, Valve Guides (1st Oversize) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Bore - Holder, Valve Guides (2nd Oversize) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Bore - Holder, Valve Guides (3rd Oversize) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Clearance - Valve => Valve Guides | ||
| ····Inlet | ||
| ····Wear limitation - Inlet | ||
| ····Exhaust | ||
| ····Wear limitation - Outlet | ||
| Valve seat | ||
| ··Valve Seat Angle (B) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Seat - Measurement (A) | ||
| ····Wear limitation | ||
| ··Bore - Holder, Valve Seat (Standard Size) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Bore - Holder, Valve Seat (1st Oversize) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Bore - Holder, Valve Seat (2nd Oversize) | ||
| ····Inlet | ||
| ····Exhaust | ||
| Camshaft-- | ||
| ··Diameter, Bearing Journal - Camshaft (Standard Size) | ||
| ··Cam Lobe Height (Total) | ||
| ····Inlet | ||
| ····Inlet | ||
| ····Inlet - min. | ||
| ····Inlet - min. | ||
| ····Exhaust | ||
| ····Exhaust | ||
| ····Exhaust - Min. | ||
| ····Exhaust - Min. | ||
| =<>= | ||
| General Information - Engine Block | ||
| ··Engine Block - Height | ||
| ··Roughness cylinder head fitting face | ||
| Cylinder Sleeve---------- | ||
| ··Bore | ||
| ··Measurement - Conical | ||
| Piston---- | ||
| ··Diameter - Piston | ||
| ····Standard Size | ||
| ··Clearance - Piston | ||
| Gudgeon Pin-------------- | ||
| ··Diameter - Gudgeon Pin | ||
| Piston Ring Set---------- | ||
| ··Piston Ring, Groove | ||
| ··1st Piston Ring, Lock - Clearance (Compression) | ||
| ····Wear limitation | ||
| ··2nd Piston Ring, Lock - Clearance (Compression) | ||
| ····Wear limitation | ||
| ··Piston Ring, Lock - Clearance (Oil Trap) | ||
| ····Wear limitation | ||
| ··1st Piston Ring, Height - Clearance (Compression) | ||
| ··2nd Piston Ring, Height - Clearance (Compression) | ||
| Connecting Rod----------- | ||
| ··Clearance, Radial - Big End Bearing | ||
| ····Wear limitation | ||
| ····Wear limitation | ||
| ··Clearance, Axial - Big End Bearing | ||
| ··Diameter, Bearing Journal - Connecting Rod | ||
| Crankshaft | ||
| ··Centering - Crankshaft (Tolerance) | ||
| ··Grindable | ||
| ··Diameter, Bearing Journal - Crankshaft (Standard Size) | ||
| ··Clearance - Main Bearing, crankshaft | ||
| ····Wear limitation | ||
| ··Bearing clearance - Axial Bearing | ||
| ····Wear limitation | ||
| Cooling System----------- | ||
| ··Type | ||
| ··Clearance, Axial - Outer, Rotor (Housing, Oil Pump) | ||
| ··Clearance - inner, Rotor => Housing, Oil Pump | ||
| Timing Gear, Kit (Control)- | ||
| ··Clearance - Gear wheel (Tooth Pitch) | ||
| ····Wear limitation | ||
| =<>= | ||
| Engine Timing Control | ||
| Cylinder Head Bolts------ | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| ····Stage 3 | ||
| Main Bearing Cap, crankshaft -------------------------------- | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| Crankshaft | ||
| Cranskhaft Pulley-------- | ||
| ··Knock Sensor | ||
| Flywheel-- | ||
| Driver Plate------------- | ||
| Camshaft, Bearing Cap---- | ||
| Camshaft, Bearing Cap---- | ||
| Rocker Arm Shaft, valve train ------------------------------- | ||
| ··Rocker Arm Bridge | ||
| Pulley, Camshaft--------- | ||
| Camshaft (Housing)------- | ||
| Timing Case-------------- | ||
| ··Guide Pulley | ||
| Spark Plug | ||
| Water Pump | ||
| Cooling System----------- | ||
| ··Thermostat Housing | ||
| Oil Pump-- | ||
| ··Cover | ||
| ··Sender Unit, oil pressure | ||
| ··Oil Pressure, Relief Valve | ||
| Oil Pan--- | ||
| ··Oil Drain Plug, oil pan | ||
| ··Oil Strainer | ||
| Exhaust Manifold--------- | ||
| Intake Manifold---------- | ||
| Hook fixing, Engine Block |
Gain access
Enginedesk contains rich-data for parts and engines. The service is particulary useful for engine rebuilders and maintenance shops.
You can browse all information online. To get access to the technical data and parts information we provide the following options:
- Anytime 'all access' € 25,- * per month.
- Anytime 'all access' € 250,- * yearly.
* Excluding sales tax (21%)
Parts manufacturer
Reach thousands of remanufacturing companies. Promote your aftermarket parts and services world wide.
Please contact Enginedesk via info@enginedesk.com.
