Technical Data - NISSAN CG13DE (DOHC)
Manufacturer NISSAN
CG13DE (DOHC) - I - DOHC
| Engine Type | CG13DE (DOHC) |
| Fuel Supply System | I |
| Note | DOHC |
| Cc | 1275 |
| Number of Cylinders | 4 |
| Bore Ø | 71.00 |
| Stroke | 80.50 |
| KW | 55 |
| Compression | 9.50 |
| KBA No. (Germany) | 4114371 |
| Type Mines | 905A3C |
| Technical Information Number | Technical Data | Information |
|---|---|---|
| Compression-------------- | ||
| ····Compression - Ratio | ||
| ····Compression - Pressure [bar] | ||
| ····Cylinder - Differential pressure | ||
| ····Wear limitation | ||
| Refs------ | ||
| ····Idle, min. | ||
| ····Manual Transmission | ||
| ····Automatic Transmission | ||
| ····Idle, Max. | ||
| Exhaust Gas, value------- | ||
| ····CO Measurement, Idle | ||
| ····CO2 Measurement, Idle [%] | ||
| ····HC Measurement, Idle | ||
| Oil Pressure------------- | ||
| ····Idle, min. | ||
| ····Rated Capacity | ||
| Thermostat | ||
| ····Thermostat, Opening Temperature | ||
| Ignition Timing---------- | ||
| ····Ignition System | ||
| Ignition - Row----------- | ||
| =<>= | ||
| General Information - Cylinder Head ------------------------- | ||
| ··warpage (value) - Cylinder Head | ||
| ····Standard Size | ||
| ····Wear limitation | ||
| Valves---- | ||
| ··Valve Clearance [mm] | ||
| ····Operating Mode / Cold Check | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Actuation, Setting | ||
| ····Inlet / Open (° before TDC) | ||
| ····Inlet / Closed (° after BDC) | ||
| ····Exhaust / Open (° before BDC) | ||
| ····Exhaust / Closed (° after TDC) | ||
| ··Valve Head Diameter [D] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valves - Length (L) | ||
| ····Inlet - New Part | ||
| ····Exhaust - New Part | ||
| ··Valve stem diameter [d] - Inlet | ||
| ··Valve stem diameter [d] - Exhaust | ||
| ··Valve Seat Angle [°] | ||
| ··Valve Disc, Thickness (t) | ||
| ····Wear limitation - Inlet | ||
| Valve Spring------------- | ||
| ··Tolerance - Vertical (s) | ||
| ··Valve Spring - Length (Load/Empty) | ||
| ··Diameter - Spring, Material | ||
| ··Capacitive Load => Length 1 [mm] | ||
| ····Wear limitation | ||
| Valve Guides------------- | ||
| ··Fitted Height | ||
| ··Inner Diameter - Standard Size | ||
| ··Outer Diameter - Standard Size | ||
| ··Outer Diameter - 1st Oversize | ||
| ··Bore - Holder, Valve Guides (Standard Size) | ||
| ··Bore - Holder, Valve Guides (1st Oversize) | ||
| ··Clearance - Valve => Valve Guides | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Press-fitted, Valve Guides | ||
| ····Oversize | ||
| Valve seat | ||
| ··Valve Seat Angle (B) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Adaptation - Angle (B1) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Adaptation - Angle (B2) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Seat - Measurement (A) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Seat - Diameter (D) | ||
| ····Inlet | ||
| ··Valve Seat - Diameter (D2) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Bore - Holder, Valve Seat (1st Oversize) | ||
| ····Inlet | ||
| ····Exhaust | ||
| Valve Lifter------------- | ||
| ··Diameter - Valve Lifter | ||
| ··Bore - Holder, Rocker/ Tappet | ||
| ··Clearance, Radial - Valve Lifter | ||
| Camshaft-- | ||
| ··Bore - Holder, Camshaft Bushes (Standard Size) | ||
| ····1st Bearing | ||
| ····2nd Bearing | ||
| ····3rd Bearing | ||
| ····4th Bearing | ||
| ····5th Bearing | ||
| ··Diameter, Bearing Journal - Camshaft (Standard Size) | ||
| ····1st Bearing | ||
| ····2nd Bearing | ||
| ····3rd Bearing | ||
| ····4th Bearing | ||
| ····5th Bearing | ||
| ··Clearance, Radial - Camshaft Bushes | ||
| ····Wear limitation | ||
| ··Clearance, Axial - Camshaft Bushes | ||
| ····Wear limitation | ||
| ··Centering - Camshaft (Tolerance) | ||
| ····Wear limitation | ||
| ··Cam Lobe Height (Total) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ····Wear limitation | ||
| =<>= | ||
| General Information - Engine Block | ||
| ··Engine Block - Height | ||
| ····New Part | ||
| Cylinder Sleeve---------- | ||
| ··Bore | ||
| ··Bore | ||
| ····Standard Size | ||
| ····Standard Size | ||
| ····Standard Size | ||
| ····Wear limitation | ||
| ··Measurement - Oval, Bore (Cylinder Sleeve) | ||
| ····Standard Size | ||
| ··Measurement - Conical | ||
| ····Standard Size | ||
| Piston---- | ||
| ··Diameter - Piston | ||
| ····Standard Size | ||
| ····Standard Size | ||
| ····Standard Size | ||
| ····1st Oversize | ||
| ····Measurement (Position) | ||
| ··Clearance - Piston | ||
| Gudgeon Pin-------------- | ||
| ··Diameter - Gudgeon Pin (Eye) | ||
| ··Clearance, Radial - Gudgeon Pin | ||
| ····Clearance, Radial - Piston Rod / Piston | ||
| ····Clearance, Radial - Small End Bush / Gudgeon Pin | ||
| Piston Ring Set---------- | ||
| ··Piston Ring, Groove | ||
| ··1st Piston Ring, Lock - Clearance (Compression) | ||
| ····Wear limitation | ||
| ··2nd Piston Ring, Lock - Clearance (Compression) | ||
| ····Wear limitation | ||
| ··Piston Ring, Lock - Clearance (Oil Trap) | ||
| ····Wear limitation | ||
| ··1st Piston Ring, Height - Clearance (Compression) | ||
| ····Wear limitation | ||
| ··2nd Piston Ring, Height - Clearance (Compression) | ||
| ····Wear limitation | ||
| Connecting Rod----------- | ||
| ··Distance, Centre - Small End Bush / Big End Bearing | ||
| ··Inner Diameter - Big End Bearing | ||
| ··Clearance, Radial - Big End Bearing | ||
| ··Clearance, Radial - Big End Bearing | ||
| ····Wear limitation | ||
| ····Wear limitation | ||
| ··Clearance, Axial - Big End Bearing | ||
| ··Diameter, Bearing Journal - Connecting Rod | ||
| ····Standard Size | ||
| ··Bearing Journal, Connecting Rod - Tolerance (Oval) | ||
| ····Bearing Journal, Connecting Rod - Oval (Max.) | ||
| ··Bearing Journal, Connecting Rod - Conical (Max.) | ||
| ··Small End Bushes | ||
| ····Inner Diameter | ||
| Crankshaft | ||
| ··Number of bearings | ||
| ··Centering - Crankshaft (Tolerance) | ||
| ··Diameter, Bearing Journal - Crankshaft (Standard Size) | ||
| ··Diameter, Bearing Journal - Crankshaft (Standard Size) | ||
| ··Diameter, Bearing Journal - Crankshaft (Standard Size) | ||
| ··Diameter, Bearing Journal - Crankshaft (Standard Size) | ||
| ··Diameter, Bearing Journal - Crankshaft (Standard Size) | ||
| ··Bearing Journal, Crankshaft - Conical (Max.) | ||
| ··Bearing Journal, Crankshaft - Oval (Max.) | ||
| ··Clearance - Main Bearing, crankshaft | ||
| ····Wear limitation | ||
| ··Bearing clearance - Axial Bearing | ||
| ····Wear limitation | ||
| =<>= | ||
| Cylinder Head Bolts------ | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| ····Release | ||
| ····Stage 3 | ||
| ····Stage 5 | ||
| ····Stage 6 | ||
| Main Bearing Cap, crankshaft -------------------------------- | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| Flywheel-- | ||
| Driver Plate------------- | ||
| Camshaft, Bearing Cap---- | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| ····Stage 3 |
Gain access
Enginedesk contains rich-data for parts and engines. The service is particulary useful for engine rebuilders and maintenance shops.
You can browse all information online. To get access to the technical data and parts information we provide the following options:
- Anytime 'all access' € 25,- * per month.
- Anytime 'all access' € 250,- * yearly.
* Excluding sales tax (21%)
Parts manufacturer
Reach thousands of remanufacturing companies. Promote your aftermarket parts and services world wide.
Please contact Enginedesk via info@enginedesk.com.
