Technical Data - RENAULT E6J.700
Manufacturer RENAULT
E6J.700 - I - SOHC/OHC
| Engine Type | E6J.700 |
| Fuel Supply System | I |
| Note | SOHC/OHC |
| Cc | 1390 |
| Number of Cylinders | 4 |
| Bore Ø | 75.80 |
| Stroke | 77.00 |
| KW | 59 |
| Compression | 9.50 |
| KBA No. (Germany) | 4114371 |
| Type Mines | 905A3C |
| Technical Information Number | Technical Data | Information |
|---|---|---|
| ····Engine Code | ||
| Compression-------------- | ||
| ····Compression - Ratio | ||
| Refs------ | ||
| ····Idle, min. | ||
| ····Manual Transmission | ||
| ····Automatic Transmission | ||
| Exhaust Gas, value------- | ||
| ····CO Measurement, Idle | ||
| Oil Pressure------------- | ||
| ····Status (Operating Mode / Cold Check) | ||
| ····Idle, min. | ||
| ····Rated Capacity | ||
| Thermostat | ||
| ····Thermostat, Opening Temperature | ||
| Ignition Timing---------- | ||
| ····Ignition System | ||
| Ignition - Row----------- | ||
| =<>= | ||
| ··Cylinder Head - Height | ||
| ··warpage (value) - Cylinder Head | ||
| ····Wear limitation | ||
| ····Notes | ||
| Valves---- | ||
| ··Valve Clearance [mm] | ||
| ····Operating Mode / Cold Check | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Head Diameter [D] | ||
| ····Inlet | ||
| ····Inlet 2 | ||
| ··Valve stem diameter [d] - Inlet | ||
| ··Valve stem diameter [d] - Exhaust | ||
| ··Valve Seat Angle [°] | ||
| ····Inlet | ||
| ····Exhaust | ||
| Valve Spring------------- | ||
| ··Valve Spring - Length (Load/Empty) | ||
| ····New Part | ||
| ····Oversize | ||
| ··Min. Length [mm] => Capacitive Load 1 | ||
| ····New Part | ||
| ····Oversize | ||
| ··Min. Length [mm] => Capacitive Load 2 | ||
| ····New Part | ||
| ····Oversize | ||
| Valve Guides------------- | ||
| ··Fitted Height | ||
| ····Inlet | ||
| ····Inlet | ||
| ····Exhaust | ||
| ····Exhaust | ||
| ··Inner Diameter - Standard Size | ||
| ··Outer Diameter - Standard Size | ||
| ··Bore - Holder, Valve Guides (Standard Size) | ||
| Valve seat | ||
| ··Valve Seat Angle (B) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Seat - Measurement (A) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Seat - Diameter (D) | ||
| ····Inlet | ||
| ····Exhaust | ||
| Camshaft-- | ||
| ··Clearance, Axial - Camshaft Bushes | ||
| =<>= | ||
| General Information - Engine Block | ||
| ··Bore - Holder, Cylinder Sleeve | ||
| ··Bore - Holder, Cylinder Sleeve | ||
| ··Cylinder Sleeve Protrusion | ||
| ····Notes | ||
| ····Height - Cylinder Sleeve (different) | ||
| Cylinder Sleeve---------- | ||
| ··Cylinder Sleeve, Length | ||
| ··Cylinder Sleeve, Length | ||
| ··Inner Diameter - Cylinder Sleeve | ||
| ····Standard Size | ||
| Piston---- | ||
| ··Fitting Position | ||
| Gudgeon Pin-------------- | ||
| ··Clearance, Radial - Gudgeon Pin | ||
| ····Clearance, Radial - Piston Rod / Piston | ||
| Piston Ring Set---------- | ||
| ··Height, 1st Piston Ring (Compression) | ||
| ··Height, 2nd Piston Ring (Compression) | ||
| ··Height, Piston Ring (Oil Trap) | ||
| Connecting Rod----------- | ||
| ··Clearance, Radial - Big End Bearing | ||
| ··Diameter, Bearing Journal - Connecting Rod | ||
| ····Standard Size | ||
| ····1st Undersize | ||
| Crankshaft | ||
| ··Number of bearings | ||
| ··Diameter, Bearing Journal - Crankshaft (Standard Size) | ||
| ··Diameter, Bearing Journal - Crankshaft (1st Undersize) | ||
| ··Bearing clearance - Axial Bearing | ||
| ····New Part | ||
| Cooling System----------- | ||
| ··Type | ||
| ··Clearance, Axial - Gear wheels => Oil Pump Housing Lid | ||
| ····Wear limitation | ||
| ··Clearance - Drive gear => Housing, Pump | ||
| ····Wear limitation | ||
| ··Clearance - Driven Gear wheel => Housing, Pump | ||
| ····Wear limitation | ||
| =<>= | ||
| Engine Timing Control | ||
| Cylinder Head Bolts------ | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| ····Cooling Phase | ||
| ····Stage 4 | ||
| ····Stage 4 | ||
| ····Release | ||
| ····Stage 5 | ||
| ····Stage 5 | ||
| ····Release | ||
| ····Stage 6 | ||
| ····Stage 6 | ||
| ····Release | ||
| Main Bearing Cap, crankshaft -------------------------------- | ||
| Bearing Cap, connecting rod | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| Crankshaft | ||
| Crankshaft Gear---------- | ||
| Flywheel-- | ||
| Camshaft-- | ||
| ··Adjusting Screw, valve clearance, Lock Screw | ||
| Camshaft, Bearing Cap---- | ||
| ····Stage 1 | ||
| Drive gear - Camshaft---- | ||
| Oil Pump-- | ||
| Oil Pan--- | ||
| ··Oil Drain Plug, oil pan | ||
| Exhaust Manifold--------- | ||
| Intake Manifold---------- |
Gain access
Enginedesk contains rich-data for parts and engines. The service is particulary useful for engine rebuilders and maintenance shops.
You can browse all information online. To get access to the technical data and parts information we provide the following options:
- Anytime 'all access' € 25,- * per month.
- Anytime 'all access' € 250,- * yearly.
* Excluding sales tax (21%)
Parts manufacturer
Reach thousands of remanufacturing companies. Promote your aftermarket parts and services world wide.
Please contact Enginedesk via info@enginedesk.com.
