Technical Data - TOYOTA 4A-GE (DOHC) [1987 ->]
Manufacturer TOYOTA
4A-GE (DOHC) [1987 ->] - I -
| Engine Type | 4A-GE (DOHC) [1987 ->] |
| Fuel Supply System | I |
| Note |
| Cc | 1587 |
| Number of Cylinders | 4 |
| Bore Ø | 81.00 |
| Stroke | 77.00 |
| KW | 92 |
| Compression |
| KBA No. (Germany) | 4114371 |
| Type Mines | 905A3C |
| Technical Information Number | Technical Data | Information |
|---|---|---|
| ····Engine Code | ||
| Compression-------------- | ||
| ····Compression - Ratio | ||
| ····Compression - Pressure [bar] | ||
| ····Cylinder - Differential pressure | ||
| ····Wear limitation | ||
| Refs------ | ||
| ····Idle, min. | ||
| ····Manual Transmission | ||
| Exhaust Gas, value------- | ||
| ····CO Measurement, Idle | ||
| ····CO2 Measurement, Idle [%] | ||
| ····HC Measurement, Idle | ||
| ····O2 Measurement, Idle | ||
| Oil Pressure------------- | ||
| ····Status (Operating Mode / Cold Check) | ||
| ····Idle, min. | ||
| ····Rated Capacity | ||
| Thermostat | ||
| ····Thermostat, Opening Temperature | ||
| Ignition Timing---------- | ||
| ····Ignition System | ||
| Ignition - Row----------- | ||
| ····Ignition Point, Static / Dynamic | ||
| =<>= | ||
| General Information - Cylinder Head ------------------------- | ||
| ··warpage (value) - Cylinder Head | ||
| ····Standard Size | ||
| ····Wear limitation | ||
| Valves---- | ||
| ··Valve Clearance [mm] | ||
| ····Operating Mode / Cold Check | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valves - Length (L) | ||
| ····Inlet - New Part | ||
| ····Wear limitation - Inlet | ||
| ····Exhaust - New Part | ||
| ····Wear limitation - Outlet | ||
| ··Valve stem diameter [d] - Inlet | ||
| ····Standard Size | ||
| ··Valve stem diameter [d] - Exhaust | ||
| ····Standard Size | ||
| ··Valve Seat Angle [°] | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Disc, Thickness (t) | ||
| ····Inlet | ||
| ····Wear limitation - Inlet | ||
| ····Exhaust | ||
| ····Wear limitation - Outlet | ||
| Valve Spring------------- | ||
| ··Tolerance - Vertical (s) | ||
| ··Valve Spring - Length (Load/Empty) | ||
| ····Inlet - inner | ||
| ····Inlet - Outer | ||
| ··Diameter - Spring, Material | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Capacitive Load => Length 1 [mm] | ||
| ····Inlet - Outer | ||
| ····Exhaust - Outer | ||
| Valve Guides------------- | ||
| ··Inner Diameter - Standard Size | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Clearance - Valve => Valve Guides | ||
| ····Inlet | ||
| ····Wear limitation - Inlet | ||
| ····Exhaust | ||
| ····Wear limitation - Outlet | ||
| Valve seat | ||
| ··Valve Seat Angle (B) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Adaptation - Angle (B1) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Adaptation - Angle (B2) | ||
| ····Inlet | ||
| ····Exhaust | ||
| ··Valve Seat - Measurement (A) | ||
| ····Inlet | ||
| ····Exhaust | ||
| Valve Lifter------------- | ||
| ··Diameter - Valve Lifter | ||
| ····Standard Size | ||
| ··Bore - Holder, Rocker/ Tappet | ||
| ····Standard Size | ||
| ··Clearance, Radial - Valve Lifter | ||
| ····Wear limitation | ||
| Camshaft-- | ||
| ··Diameter, Bearing Journal - Camshaft (Standard Size) | ||
| ··Clearance, Radial - Camshaft Bushes | ||
| ····Wear limitation | ||
| ··Clearance, Axial - Camshaft Bushes | ||
| ····Wear limitation | ||
| ··Centering - Camshaft (Tolerance) | ||
| ··Cam Lobe Height (Total) | ||
| ····Wear limitation | ||
| =<>= | ||
| General Information - Engine Block | ||
| ··Bore - Holder, Main Bearings (Engine Block) | ||
| ····Undersize | ||
| Cylinder Sleeve---------- | ||
| ··Bore | ||
| ····Standard Size | ||
| ····Wear limitation | ||
| ····1st Oversize | ||
| ····1st Oversize | ||
| Piston---- | ||
| ··Diameter - Piston | ||
| ····Standard Size | ||
| ····1st Oversize | ||
| ··Clearance - Piston | ||
| Gudgeon Pin-------------- | ||
| ··Diameter - Gudgeon Pin | ||
| ··Clearance, Radial - Gudgeon Pin | ||
| ····Wear limitation | ||
| Piston Ring Set---------- | ||
| ··Piston Ring, Groove | ||
| ··1st Piston Ring, Lock - Clearance (Compression) | ||
| ····Wear limitation | ||
| ··2nd Piston Ring, Lock - Clearance (Compression) | ||
| ····Wear limitation | ||
| ··Piston Ring, Lock - Clearance (Oil Trap) | ||
| ····Wear limitation | ||
| ··1st Piston Ring, Height - Clearance (Compression) | ||
| ··2nd Piston Ring, Height - Clearance (Compression) | ||
| Connecting Rod----------- | ||
| ··Bending radius | ||
| ····Wear limitation | ||
| ··Twist | ||
| ····Wear limitation | ||
| ··Inner Diameter - Big End Bearing | ||
| ··Clearance, Radial - Big End Bearing | ||
| ····Wear limitation | ||
| ····Wear limitation | ||
| ····Oversize | ||
| ··Clearance, Axial - Big End Bearing | ||
| ··Diameter, Bearing Journal - Connecting Rod | ||
| ····Standard Size | ||
| ····1st Undersize | ||
| ··Bearing Journal, Connecting Rod - Tolerance (Oval) | ||
| ····Bearing Journal, Connecting Rod - Oval (Max.) | ||
| ····Wear limitation | ||
| ··Bearing Journal, Connecting Rod - Conical (Max.) | ||
| ····Wear limitation | ||
| ··Thickness, Big End Bearings | ||
| ··Thickness, Big End Bearings | ||
| ··Thickness, Big End Bearings | ||
| ··Small End Bushes | ||
| ····Inner Diameter | ||
| Crankshaft | ||
| ··Number of bearings | ||
| ··Centering - Crankshaft (Tolerance) | ||
| ··Diameter, Bearing Journal - Crankshaft (Standard Size) | ||
| ··Diameter, Bearing Journal - Crankshaft (1st Undersize) | ||
| ··Bearing Journal, Crankshaft - Conical (Max.) | ||
| ····Wear limitation | ||
| ··Bearing Journal, Crankshaft - Oval (Max.) | ||
| ····Wear limitation | ||
| ··Clearance - Main Bearing, crankshaft | ||
| ····New Part | ||
| ····Wear limitation | ||
| ····Undersize | ||
| ··Bearing clearance - Axial Bearing | ||
| ····Wear limitation | ||
| Main Bearing scales, crankshaft ----------------------------- | ||
| ··Thickness, Axial Bearing (Bearing Shell) | ||
| ····Standard Size | ||
| ····Standard Size | ||
| ····Standard Size | ||
| ····Standard Size | ||
| ····Standard Size | ||
| ····Oversize | ||
| =<>= | ||
| Engine Timing Control | ||
| Cylinder Head Bolts------ | ||
| ····Stage 1 | ||
| ····Stage 2 | ||
| ····Stage 3 | ||
| Main Bearing Cap, crankshaft -------------------------------- | ||
| Bearing Cap, connecting rod | ||
| Crankshaft | ||
| Crankshaft Gear---------- | ||
| Flywheel-- | ||
| Camshaft, Bearing Cap---- | ||
| Drive gear - Camshaft---- | ||
| Alternator | ||
| Spark Plug | ||
| Oil Pump-- | ||
| Exhaust Manifold--------- | ||
| Intake Manifold---------- |
Gain access
Enginedesk contains rich-data for parts and engines. The service is particulary useful for engine rebuilders and maintenance shops.
You can browse all information online. To get access to the technical data and parts information we provide the following options:
- Anytime 'all access' € 25,- * per month.
- Anytime 'all access' € 250,- * yearly.
* Excluding sales tax (21%)
Parts manufacturer
Reach thousands of remanufacturing companies. Promote your aftermarket parts and services world wide.
Please contact Enginedesk via info@enginedesk.com.
